Transformer Power Transformer LED Driver 300MA 4-7W LED Power Supply DC12-25V Lighting Transformers for LED Bulbs
Brand new and high quality Transformer for LED bulbs Input voltage: 85-265V AC 50 / 60Hz Output voltage: 12-25V DC Power: about 4-7W Output current: +/- 5% 260-310MA Colour: white Material: plastic Size: 6x3x 2.3 cm Package Contents: 4 * Transformer (with 4 Cable) Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
20pcs DC 9V 12V 18V 24V 20W Adjustable LED Driver PWM Controller DC DC Step Down Module Constant Current Converter Board
Description:;; - 6-25V 900mA Step-down High Brightness LED Driver with 5000:1 Dimming; - Working voltage: DC 6-25V(Perfect for 6V 9V 12V 18V 24V; LED or LED strip)- Output Current: 30-900MA; By changing the RCS resistance, the maximum current can reach 1200MA- Maximum output power: 20W- Current regulation: 1 through adjustable resistance; 2 through PWM control;; - Single pin on/off and brightness control using DC voltage or PWM- Up to 1MHz switching frequency- Typical 5% output current accuracy- Inherent open-circuit LED protection- High efficiency (up to 97%)- High-Side Current Sense- Hysteretic Control: No Compensation- Adjustable Constant LED Current; - Size: 30 x 15 x 6.3 mm; Package Included:; 20 x DC 9V 12V 18V 24V 20W Adjustable LED Driver PWM Controller DC DC Step Down Module;;
10pcs DC-DC 7.5-28V To 5V 3A Step-Down Power Supply Module Cellphone Car Charger USB Buck Regulator
Specifications: Input: 7.5V -28V; Output: 5V / 3A; Conversion efficiency: 96% (Max); Switching frequency: 1.5MHZ (Max) Typical 1MHZ; Working temperature: -40 ? - +85?; Load capacity: Maximum output 3A, 2A continuous; Scope: mobile power, mobile phones, flat-panel powered devices USB 5VProduct dimensions: 42mm x 16mm x 5mm (L x W x H) Package included: 10 x Step-down power supply module
30pcs SX1308 DC-DC 2V-24V to 2V-28V 2A Adjustable Boost Regulated Power Supply Module High Current
Introduction:; The SX1308 boost module is equipped with the SX1308 chip, which has a small package and high efficiency. The output is adjustable up to 28V, and the internal integration of very low RDS internal resistance 100m & Omega; metal oxide semiconductor field effect transistor (MOSFET) can achieve high current output within 2A. Widely in 3G network products, digital products, mobile power, battery-powered equipment.; Features:; Oscillation frequency 1.2MH z, efficiency up to 95%The circuit has short circuit protection, overheat protection and other functions10K price potentiometer, adjust voltage output; Parameters:; Input voltage range: DC 2V-24VOutput voltage range: DC 2V-28VSwitching frequency: 1.2MH zOutput current: & le ; 2APackage includes: 30 x Power supply module
5 Sets EE25 5 with 5pin Transformer Bobbin PC40 Ferrite Core Vertical 10 Ferrite Halves and 5 Bobbin
Product descriptionKEY_TAB Widely used in color TV, monitor, electric car charger, DVD, switching power supply, UP power supply, DC-DC converter, high frequency transformer, filter, inductor, household appliance, industrial automation, instrumentation, communication, energy saving Lighting and more!KEY_TAB KEY_TAB Product Range: Transformers, filter inductors, coils, bobbins, magnetic cores.Type: EE25Pin spacing: 4mm/0.16''Row spacing: 12mm/0.47"Ferrite core Size: 25 x 5.5 x 9mm/0.9" x 0.2" x 0.3"(L*W*T)Bobbin size: 24.5 x 17.5 x 24mm/0.9" x 0.6" x 0.9"(L*W*H)Winding frame size: 11 x 9 x 9mm/0.4" x 0.3" x 0.3"(L*W*H)Package content: 5 SET =10 ferrite halves + 5 bobbin
10pcs XL4015 5A DC-DC Step Down Adjustable Power Supply Module Buck Converter
Specification: Module highlights: 5A high power, high efficiency and low ripple with power indicatorModule Properties: non-isolated buck module (BUCK) Input voltage: 8-36V (input please try not to exceed 38V) Output voltage: 1.25 -32V continuously adjustableOutput Current: 0-5AOutput Power: 75WOperating temperature: -40 to +85 degreesOperating frequency: 180KHzConversion efficiency: up to 96%Load regulation: S (I) & le; 0.8 % (input 24V, output 12V, load varies from 1 ~ 4.5A measured)Voltage Regulation: S (u) & le; 0.8 % (output 12V, when 4A, when 18 ~ 32V voltage change from the measured)Power Indicator: YesShort circuit protection: Yes (limit current 8A) Overtemperature protection: (automatically shut off the output after overtemperature) Input reverse polarity protection: No, (if necessary, please enter the string into the high current diode)Installation: two 3mm screwsConnection: Welding, V-IN is the input, V-OUT is the outputModule dimensions: 54 x 23 x 15mm (L x W x H) Application: The DC/DC buck module applications the input voltage is higher than the output voltage of the buck field, such as battery, power transformer, DIY adjustable regulated power supply, 24V Vehicle notebook power supply, industrial equipment buck. 12V buck to 3.3V, 12V buck to 5V,; 24V buck to 5V, 24V buck to 12V,; 36V buck to 24V etc. Package Included: 10 x Step Down Module
10pcs IB0505LS-1W DC-DC 5V to 5V Isolation Power Supply Module Input 4.75-5.25V Output 5V
>>>Manual: Click here to open
10pcs DC 9V 12V 18V 24V 20W Adjustable LED Driver PWM Controller DC DC Step Down Module Constant Current Converter Board
Description:;; - 6-25V 900mA Step-down High Brightness LED Driver with 5000:1 Dimming; - Working voltage: DC 6-25V(Perfect for 6V 9V 12V 18V 24V; LED or LED strip)- Output Current: 30-900MA; By changing the RCS resistance, the maximum current can reach 1200MA- Maximum output power: 20W- Current regulation: 1 through adjustable resistance; 2 through PWM control;; - Single pin on/off and brightness control using DC voltage or PWM- Up to 1MHz switching frequency- Typical 5% output current accuracy- Inherent open-circuit LED protection- High efficiency (up to 97%)- High-Side Current Sense- Hysteretic Control: No Compensation- Adjustable Constant LED Current; - Size: 30 x 15 x 6.3 mm; Package Included:; 10 x DC 9V 12V 18V 24V 20W Adjustable LED Driver PWM Controller DC DC Step Down Module;;
10pcs XL4015 5A DC-DC Step Down Adjustable Power Supply Module Buck Converter
Specification: Module highlights: 5A high power, high efficiency and low ripple with power indicatorModule Properties: non-isolated buck module (BUCK) Input voltage: 8-36V (input please try not to exceed 38V) Output voltage: 1.25 -32V continuously adjustableOutput Current: 0-5AOutput Power: 75WOperating temperature: -40 to +85 degreesOperating frequency: 180KHzConversion efficiency: up to 96%Load regulation: S (I) & le; 0.8 % (input 24V, output 12V, load varies from 1 ~ 4.5A measured)Voltage Regulation: S (u) & le; 0.8 % (output 12V, when 4A, when 18 ~ 32V voltage change from the measured)Power Indicator: YesShort circuit protection: Yes (limit current 8A) Overtemperature protection: (automatically shut off the output after overtemperature) Input reverse polarity protection: No, (if necessary, please enter the string into the high current diode)Installation: two 3mm screwsConnection: Welding, V-IN is the input, V-OUT is the outputModule dimensions: 54 x 23 x 15mm (L x W x H) Application: The DC/DC buck module applications the input voltage is higher than the output voltage of the buck field, such as battery, power transformer, DIY adjustable regulated power supply, 24V Vehicle notebook power supply, industrial equipment buck. 12V buck to 3.3V, 12V buck to 5V,; 24V buck to 5V, 24V buck to 12V,; 36V buck to 24V etc. Package Included: 10 x Step Down Module
100 Pcs Encapsulate Power Transistors 75V 600MA & 20PCS Photoresistor Light-Dependent Resistor Sensor
20 pcs Light-Dependent Resistor Sensor & 100 pcs (+/-2%) Power Transistors Light-Dependent Resistor Sensor: Maximum Voltage: 150 Volt DC Maximum Wattage: 90mW Operating Temperature: -30 ~ +70 Celsius Spectral Peak: 540nm Light Resistance (10 Lux): 5-10 Kohm Dark Resistance: 0.5 Mohm 100? 10:0. 5 Response time: 30ms (Rise), 30ms (Down) Resistance Illumination: 2 size: 5mm Light-dependent resistors or photoresistors are a staple of electronics. If you need a way to sense the level of ambient light then there is no easier way to do it. As the light on the sensor increases then the resistance across the two leads decreases. If you have a rear view mirror that darkens when its hit buy headlights you can check in the little hole on face of the mirror and you'll see those wavy lines of photoresistor! (+/-2%) Power Transistors: Product Name: Power Transistors Model: 2N2222 Type: NPN Collector-emitter Voltage: 75V Collector current: 600mA Power: 625mW colour: As Shown material: Metal & metal + plastic Package Contents: 20 x Light-Dependent Resistor Sensor 100 x (+/-2%) Power Transistors Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
5pcs DC 3.3-13V to DC 15V Positive Negative Dual Output Power Supply DC DC Step Up Boost Module Voltage Converter Board
Size ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size. Specifications:; Input voltage: DC 3.3 - 13VOutput voltage: DC ±15(Deviation is ±4%); Maximum input current: 1.8AM aximum output current: +Vo is 600mA, -Vo is 120mAQuiescent current: 3-4mADC DC Boost Converter Module working frequency 400kHz. Operating temperature;: -40~+125?Storage temperature;: -65~+150 ?Pin;: 2.54 mmSize: 25 x 16.3 x 6.6 mm; Features:;;; Internal Optimize Power MOSFET; High efficiency up to 90%; Built in Frequency CompensationBuilt in Soft-Start Function; Built in Thermal Shutdown Function; Built in Current Limit Function;;;;; Note:; 1. Due to the diode partial pressure, the voltage of -Vo is lower than +Vo. 2. In order to obtain a more stable voltage, it is recommended that the output is greater than 15mA. 3. -Vo cannot be alone, or no voltage output. But you can just use +Vo.;;; Applications:;; ADC/DAC/Operational Amplifier; RS232 RS485 RS422 BusAudio equipmentLCD power supplyInstrumentation equipmentMCU BoardMotor PowerInstrumentation multimeterWifi/Router/Ethernet devices;;;; Attention:;;; 1. Input voltage can not be greater than the maximum input. 2. Output power can not be greater than the maximum load for a long time. 3. Input power must be greater than the output power, because the power consumption of the module itself.; Package Included:; 5 x DC 3.3 -13V to DC ±15V DC Step Up Voltage Converter Board;
EE65A 6 with 6pin Transformer Bobbin PC40 Ferrite Core Vertical 2 Ferrite Halves and 1 Bobbin
Product descriptionKEY_TAB Widely used in color TV, monitor, electric car charger, DVD, switching power supply, UP power supply, DC-DC converter, high frequency transformer, filter, inductor, household appliance, industrial automation, instrumentation, communication, energy saving Lighting and more!KEY_TAB KEY_TAB Product Range: Transformers, filter inductors, coils, bobbins, magnetic cores.Type: EE65ARow spacing: 32.6mm/1.3"Ferrite core Size: 65 x 19.5 x 33mm/2.5" x 0.7" x 1.2"(L*W*T)Bobbin size: 43 x 45 x 60mm/1.6" x 1.7" x 2.4"(L*W*H)Winding frame size: 38 x 23.5mm/1.5" x 0.9"(L*W*T)Package content: 1 SET = 2 ferrite halves + 1 bobbin
5pcs DC 3.3-13V to DC 15V Positive Negative Dual Output Power Supply DC DC Step Up Boost Module Voltage Converter Board
Size ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size. Specifications:; Input voltage: DC 3.3 - 13VOutput voltage: DC ±15(Deviation is ±4%); Maximum input current: 1.8AM aximum output current: +Vo is 600mA, -Vo is 120mAQuiescent current: 3-4mADC DC Boost Converter Module working frequency 400kHz. Operating temperature;: -40~+125?Storage temperature;: -65~+150 ?Pin;: 2.54 mmSize: 25 x 16.3 x 6.6 mm; Features:;;; Internal Optimize Power MOSFET; High efficiency up to 90%; Built in Frequency CompensationBuilt in Soft-Start Function; Built in Thermal Shutdown Function; Built in Current Limit Function;;;;; Note:; 1. Due to the diode partial pressure, the voltage of -Vo is lower than +Vo. 2. In order to obtain a more stable voltage, it is recommended that the output is greater than 15mA. 3. -Vo cannot be alone, or no voltage output. But you can just use +Vo.;;; Applications:;; ADC/DAC/Operational Amplifier; RS232 RS485 RS422 BusAudio equipmentLCD power supplyInstrumentation equipmentMCU BoardMotor PowerInstrumentation multimeterWifi/Router/Ethernet devices;;;; Attention:;;; 1. Input voltage can not be greater than the maximum input. 2. Output power can not be greater than the maximum load for a long time. 3. Input power must be greater than the output power, because the power consumption of the module itself.; Package Included:; 5 x DC 3.3 -13V to DC ±15V DC Step Up Voltage Converter Board;
5pcs 220V to 5V 600mA 3W AC-DC Step Down Regulated Power Supply Module LC-Powr-FT838 Precision Board
Description:; Over-voltage protection, over-current protection, over-temperature protection, short circuit protection. High thermal conductivity resin encapsulation has the characteristics of dust proof, moisture proof, shock proof and flame retardant. The average trouble-free time is more than 300, 000 hours. Ripple voltage: 80 mVWorking temperature: minimum - 20°C, maximum 70°COutput voltage: 5VOutput power: 3WSize: 20 x 30 x 15 mmOutput Voltage Range: 4.8 - 5.1V; Package included: 5 x LC-Powr-FT838 AC-DC Step Down Regulated Power Supply Module
5pcs LM2596S DC-DC 24V/12V To 5V 5A Step Down Power Supply Buck Converter Adjustable USB Step-down Charging Module
Features: Synchronous rectification scheme, wide voltage input, high current output, high efficiency. With DC plug and terminals, easy to use. With USB port, with fast-charge identification chip compatible with Andrews and iphone mobile phone.; Product parameters:; Input voltage: DC 9V - 36VThe output voltage: 5.2V / 5A / 25WOutput capability:; 9 ~ 24V Input: Output 5.2V / 6A / 30W;;;;;;;;;;;;;;; 24 ~ 32V Input: Output 5.2V / 5A / 25W;;;;;;;;;;;;;;; 32 ~ 36V Input: Output 5.2V / 3.5A / 18WSize: 63 x 27 x 10mm (L * W * H) Weight: 22g; Package included: 5 x LM2596S DC-DC 24V/12V To 5V 5A Step Down Module
5 Sets EE55B 11 with 11pin Transformer Bobbin PC40 Ferrite Core Vertical 10 Ferrite Halves and 5 Bobbin
Product descriptionKEY_TAB Widely used in color TV, monitor, electric car charger, DVD, switching power supply, UP power supply, DC-DC converter, high frequency transformer, filter, inductor, household appliance, industrial automation, instrumentation, communication, energy saving Lighting and more!KEY_TAB KEY_TAB Product Range: Transformers, filter inductors, coils, bobbins, magnetic cores.Type: EE55BPin spacing: 5mm/0.2''Row spacing: 35mm/1.4"Ferrite core Size: 55.5 x 20.5 x 28mm/2.2" x 0.8" x 1.1"(L*W*T)Bobbin size: 61 x 42 x 60mm/2.4" x 1.6" x 2.4"(L*W*H)Winding frame size: 32 x 20 x 24mm/1.2" x 0.8" x 0.9"(L*W*T)Package content: 5 SET = 10 ferrite halves + 5 bobbin
10pcs B0505S 1WR2 DC-DC Power Supply Module 5V to 5V Isolation Chip DIP-4
>>>Manual: Click here to open
5pcs 5A Range Single-phase AC Active Output Current Transformer Module
Description:; 1. onboard precision micro current transformer2. high precision op-amp circuit board, do accurate sampling for the signal and appropriate compensation, and other functions3. the module can measure within 5A current communication, corresponding to output analog quantity can be adjusted4. PCB board size: 38 (mm) x 18.5 (mm) 5. Working voltage: DC5-30V; Package included:; 5 x 5A Range Single-phase AC Active Output Current Transformer Module
3pcs XL4015 5A High Power 75W DC-DC Adjustable Step Down Module LED Voltmeter Power Supply Module
Description:; This product is a 180 KHz fixed frequency PWM buck (step-down) DC/DC module, capable of driving a 5A load with high efficiency, low ripple and excellent line and load regulation. The module with a voltage meter to display the input voltage and output voltage, and the voltage can be corrected through the button to improve the accuracy of the voltmeter.; Features:; 1. LED power indicator. 2. Button to switch measurement of the input or output voltage, and LED indicates the current measurement of the input or output voltage; The nixie tube can be turned off by another button. Mentioned states are able to be memorized, is not lost even if the power is disconnected. (On-board marked "IN" LED is turned on, the nixie tube display input voltage value, "OUT" LED bright display is the output voltage value). 3. Special launch, the voltmeter calibration function, will never exist voltmeter inaccurate! Voltmeter calibration method: (1) Output voltage calibration stepsStep 1, adjust the right button so that "OUT" LED lighted, the voltmeter shows the value of output voltage; Press the right button for more than 2 seconds, release, voltmeter and "OUT" LED flashes in synchronization so that you enter the output voltage calibration mode. Step 2, press the right button (normal speed), the voltage value is adding up a unit; Press the left button, minus a unit; Due to a unit is less than 0.1V, the minimum voltage display to 0.1V, so you need to continuously press 1-5 times to see the voltmeter change 0.1V, how many times voltmeter change 0.1V by pressing the key, depending on the current display voltage, the higher the voltage, the fewer the number of press. Step 3, press the right button for more than 2 seconds, release, to exit the output voltage calibration mode. All parameters set to automatically power down to save. (2) Input voltage calibration stepsStep 1, adjust the right button so that "IN" LED lighted, the voltmeter shows the value of input voltage; press the right button for more than 2 seconds, release, voltmeter and "IN" LED flashes in synchronization so that you enter the input voltage calibration mode. Steps 2 and 3, consistent with the output voltage calibration method.; Specifications:; 1. Input voltage range: 4~38VDC(Note: input voltage not exceeding 38V)2. Output voltage range: 1.25 -36VDC adjustable3. Output current: 0-5A4. Output power: 75W5. voltmeter range: 4 to 40V, error & plusmn; 0.1V 6. Operating frequency: 180KHz7. High efficiency up to 96%8. Built in thermal shutdown function9. Built in current limit function10. Built in output short protection function11. Input reverse polarity protection: None (if required, high current diode in series with the input). 12. L x W x H = 6.6 * 3.9 * 1.8CM;; Application:; The DC/DC buck module applications the input voltage is higher than the output voltage of the buck field, such as battery, power transformer, DIY adjustable regulated power supply, LCD Monitor and LCD TV, portable instrument power supply, telecom/networking equipment, 24V vehicl
MD01 Temperature and Humidity Transmitter SHT20 Sensor Industrial-Grade Temperature and Humidity Monitoring
The product uses industrial-grade chips and high-precision imported SHT20 temperature and humidity sensors to ensure the excellent reliability, high precision and interchangeability of the product. Using RS485 hardware interface, the protocol layer is compatible with the standard industrial Modbus-Rtu protocol. This product integrates the MODBUS protocol and the common protocol. The user can choose the communication protocol by himself. The common protocol has an automatic upload function (connecting RS485 and passing the serial port adjustment tool will automatically output temperature and humidity). Product Highlights: Industrial grade product, high progress SHT20 temperature and humidity sensor, RS485 communication; Standard MODBUS protocol and common protocol are integrated, users can choose communication protocol by themselves; The baud rate can be set by yourself; The common protocol has an automatic upload function, and the upload rate can be set by yourself. Product parameters: Working voltage: DC4-30V (the highest should not exceed 33V) Maximum power: 0.2W Working temperature: temperature -20 Celsius+60Celsius, humidity 0%RH-100%RH Control accuracy: temperature ± 0.3C elsius (25Celsius), humidity ±3%RH (25Celsius) Output interface: RS485 communication (standard MODBUS protocol and custom common protocol), see protocol description for details Device address: 1-247 can be set, the default is 1 Baud rate: default 9600 (users can set by themselves), 8 data, 1 stop, no parity Colour: Black Material: plastic Size: 60x30x18mm Package Contents: 1* sensor Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
10pcs IB0505LS-1W DC-DC 5V to 5V Isolation Power Supply Module Input 4.75-5.25V Output 5V
>>>Manual: Click here to open
Diameter 32mm 12V DC 25 RPM Gear-Box Speed Control Electric Motor Stabilivolt
Note: The color of the item may vary slightly due to photography and your own computerTechnical data:Voltage: 12VNo-load speed: 25RPMNo-load current: 0.028AMPRated speed: 18RMPRated current: 0.098AMPRated torque: 2.33kg.cmDiameter: 32mmShaft length: 23mmShaft diameter: 8mm Weight: 127gPackage includes:1 x 12V DC 25 RPM Gear-Box Electric Motor
50pcs SX1308 DC-DC 2V-24V to 2V-28V 2A Adjustable Boost Regulated Power Supply Module High Current
Introduction:; The SX1308 boost module is equipped with the SX1308 chip, which has a small package and high efficiency. The output is adjustable up to 28V, and the internal integration of very low RDS internal resistance 100m & Omega; metal oxide semiconductor field effect transistor (MOSFET) can achieve high current output within 2A. Widely in 3G network products, digital products, mobile power, battery-powered equipment.; Features:; Oscillation frequency 1.2MH z, efficiency up to 95%The circuit has short circuit protection, overheat protection and other functions10K price potentiometer, adjust voltage output; Parameters:; Input voltage range: DC 2V-24VOutput voltage range: DC 2V-28VSwitching frequency: 1.2MH zOutput current: & le ; 2APackage includes: 50 x Power supply module
60M Transmitter Receiver HDMI Extender HDMI V1.3 to Single CAT-5e/6
Description: One pair as a full functional module, no need of setting. CAT-5e/6 cable can substitute HDMI cable to achieve long distance transmission. This item's transmission distance up to 60m; Comform to IEEE-568B standard. Transmission distance can be up to 60 meters for 1080P@60Hz. Support HDMI 1.2, 1.3 b, 1.4. Support 3D, highest video resolution up to 1080P@60Hz. Support 225MHz/ 2.25G bps per channel bandwidth ( 6.75G pbs all channel). Support 12bit per channel deep color (36bit all channel). Support uncompressed audio such as LPCM. Support compressed audio such as DTS Digital, Dolby Digital(including DTS-HD and Dolby True HD). Connection and operation: Connect the HDMI input sources such as: HD-DVD, PS3, STB etc. Connect two CAT-5E cables to both the output of the sender and input of the receiver. Connect the HDMI output(such as: HD-LCD HD-DLP)into receiver. Dimensions: 8.2 cm x 5.1 cm x 2.3 cm Weight: 226 g Packing List: 1 x Transmitter 1 x Receiver 2 x 100~240V EU plug power adapter (117cm-cable) 1 x English user manual
Chicong Technology Co., LTD
1 Pcs IR Transmitter Module 38KHz PCB 4 X 1,5 X 0,5 cm 4G & 1 Pcs HC-SR505 Mini Infrared PIR Motion Sensor
1 pcs IR Transmitter Module 38KHz PCB 4 x 1, 5 x 0, 5 cm 4G & 1 pcs HC-SR505 Mini Infrared PIR Motion Sensor Operating Voltage Range: DC 4.5 -20V Static current: Less than 50uA Output level: High 3.3V / Low 0V Trigger: repeatable trigger (default) transmitter module: Brand new IR transmitter module of good quality. It can send 38 KHz modulation signal and is perfect for Arduino DIY project. Dimensions: 4 x 1.5 x 0.5 cm Material: PCB Color: Black + Silver Grey Feature: Sends 38 KHz modulation signal Suitable for Arduino DIY project Infrared detector module: Delay time: Default 8S + -30% (can be customized range of a few tenths - tens of minutes) PCB Dimensions: 10 x 23mm Induction angle: Less than 100 degree cone angle Induction distance: 3 meters Working temperature: -20 - +80 degrees Sensor Lens Dimensions: Diameter: 10mm (default) Material: metal colour: green Package Contents: 1 x transmitter module 1 x Infrared detector module Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
10pcs DC-DC 7.5-28V To 5V 3A Step-Down Power Supply Module Cellphone Car Charger USB Buck Regulator
Specifications: Input: 7.5V -28V; Output: 5V / 3A; Conversion efficiency: 96% (Max); Switching frequency: 1.5MHZ (Max) Typical 1MHZ; Working temperature: -40 ? - +85?; Load capacity: Maximum output 3A, 2A continuous; Scope: mobile power, mobile phones, flat-panel powered devices USB 5VProduct dimensions: 42mm x 16mm x 5mm (L x W x H) Package included: 10 x Step-down power supply module
5 Sets RM8 6 with 6pin Transformer Bobbin PC40 Ferrite Core Vertical 10 Ferrite Halves and 5 Bobbin
Product descriptionKEY_TAB Widely used in color TV, monitor, electric car charger, DVD, switching power supply, UP power supply, DC-DC converter, high frequency transformer, filter, inductor, household appliance, industrial automation, instrumentation, communication, energy saving Lighting and more!KEY_TAB KEY_TAB Product Range: Transformers, filter inductors, coils, bobbins, magnetic cores.Type: RM8Pin spacing: 2.5mm/0.09''Ferrite core Size: 23 x 15 x 8mm/0.9" x 0.6" x 0.3"(L*W*T)Bobbin size: 25 x 17 x 17mm/0.9" x 0.6" x 0.6"(L*W*H)Winding frame size: 9 x 10mm/0.3" x 0.4"(L*W)Package content: 5 SET =10 ferrite halves + 5 bobbin
10pcs DC 3.3-13V to DC 15V Positive Negative Dual Output Power Supply DC DC Step Up Boost Module Voltage Converter Board
Size ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size. Specifications:; Input voltage: DC 3.3 - 13VOutput voltage: DC ±15(Deviation is ±4%); Maximum input current: 1.8AM aximum output current: +Vo is 600mA, -Vo is 120mAQuiescent current: 3-4mADC DC Boost Converter Module working frequency 400kHz. Operating temperature;: -40~+125?Storage temperature;: -65~+150 ?Pin;: 2.54 mmSize: 25 x 16.3 x 6.6 mm; Features:;;; Internal Optimize Power MOSFET; High efficiency up to 90%; Built in Frequency CompensationBuilt in Soft-Start Function; Built in Thermal Shutdown Function; Built in Current Limit Function;;;;; Note:; 1. Due to the diode partial pressure, the voltage of -Vo is lower than +Vo. 2. In order to obtain a more stable voltage, it is recommended that the output is greater than 15mA. 3. -Vo cannot be alone, or no voltage output. But you can just use +Vo.;;; Applications:;; ADC/DAC/Operational Amplifier; RS232 RS485 RS422 BusAudio equipmentLCD power supplyInstrumentation equipmentMCU BoardMotor PowerInstrumentation multimeterWifi/Router/Ethernet devices;;;; Attention:;;; 1. Input voltage can not be greater than the maximum input. 2. Output power can not be greater than the maximum load for a long time. 3. Input power must be greater than the output power, because the power consumption of the module itself.; Package Included:; 10 x DC 3.3 -13V to DC ±15V DC Step Up Voltage Converter Board;
20pcs DC-DC 0.9V-5V to 5V 600mA USB Step Up Power Boost Module PFM Control Mobile Booster
Feature: & nbsp; Input voltage: 0.9 -5V DC PFM Control Output voltage: 5V DC Output Current: 500-600mA High conversion efficiency, maximum to 96% & nbsp; Applications: & nbsp; DIY a mobile power supply, only need one battery, you can output 5V voltage for your phone, MP3, MP4, charger, very easy. In order to power your electronic devices when your device needs 5V power supply, when you only have lithium battery, this module can be directly step-up to 5V, solve your problems. & nbsp; Package Includes: & nbsp; 20 x DC-DC USB Step-up Power Boost Module
9-36V To 12V DC Buck Power Converter Waterproof Multiple Protection 3A Step Down Module Voltage Adapter for Car Alarms LED Car Display
Features:; 1. Thin, small size, high efficiency and easy to install. 2. Multiple protection: over current protection/over voltage protection/over high temperature/ short-circuit protection. 3. Purpose: car alarms, radio, intercom, electric motors, audio, navigation, surveillance, LED car display, air conditioning, fans, solar energy, DVD, LED lights, motors, pumps, and industrial electrical equipment, etc.; Specification:; Material: aluminumColor: silverShell size: 74x74x 32mm (LxWxH) Input voltage: DC12-24V (wide voltage: 9-36V)Output voltage: DC12VOutput current:; 3APower: 36WTransform efficiency: over 93%Ripple: 40MVPower consumption: 15MAWorking temp: -40 ? ~+ 85 ?Installation wire length: 13 -14cmWaterproof: IP67Input wire color: (+) Red, (-) Black. Output wire color: (+) Yellow, (-) Black. Note: Please be remind to make sure wiring carefully & correctly. No wiring reverses protection for this device. Package Included:; 1 x 9-36V To 12V DC Buck Power Converter Waterproof
AC 110/220V 24VDC 3A 72W Power Supply Transformer for LED Flexible Strip Lamp
AC 110/220V 24VDC 3A 72W Power Supply Transformer for LED Flexible Strip Lamp Product Name: Power Supply; Input: AC 110/220V±15% Output: DC 24V, 3A; Main Material: Aluminum Size: 15.5 x 9.5 x 4cm/ 6.1 '' x 3.7 '' x 1.6 '' (L*W*H); Color: Silver Tone Package Content: 1 x Power Supply" "Single output, aluminum housing, AC to DC power supply. With overload and short circuit protection. Mainly used for CCTV camera, LED flexible strip, LED decorative lighting, building lighting, stage lighting, LED display and home appliances.
5pcs BESTEP 2 Channel 3V Relay Module Low Level Trigger Optocoupler Isolation For Auduino
Module parameters: & nbsp; 1. Size: 50.5 x 38.5 x 18.5 mm (length x width x height) 2. Weight: 31g 3. PCB color: Black 4. There are 4 fixing screw holes around the board, the hole diameter is 3.1 mm, which is convenient for installation and fixing. 5. Relay with a common end, a normally open end, and a normally closed end 6. Optocoupler isolation, good anti-interference 7. Low level pull-in, high level release. The status indicator is on when the inverter is closed, and the status indicator is off when released. 8. VCC is the system power supply and JD_VCC is the relay power supply, use with the cap & nbsp; Electrical parameters: & nbsp; Supply voltage: 3V Current: greater than 100mA Load: 250V 10A AC or 30V 10A DC & nbsp; Wiring instructions: & nbsp; VCC: System power supply positive GND: System power supply negative IN1--IN2: Relay Control Port (Do not reverse the connection, the reverse connection will cause the module to burn out. ) & nbsp; Package includes: & nbsp; 5 x Relay Module
10pcs IB0505LS-1W DC-DC 5V to 5V Isolation Power Supply Module Input 4.75-5.25V Output 5V
>>>Manual: Click here to open
10pcs DC 3.3-13V to DC 15V Positive Negative Dual Output Power Supply DC DC Step Up Boost Module Voltage Converter Board
Size ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size. Specifications:; Input voltage: DC 3.3 - 13VOutput voltage: DC ±15(Deviation is ±4%); Maximum input current: 1.8AM aximum output current: +Vo is 600mA, -Vo is 120mAQuiescent current: 3-4mADC DC Boost Converter Module working frequency 400kHz. Operating temperature;: -40~+125?Storage temperature;: -65~+150 ?Pin;: 2.54 mmSize: 25 x 16.3 x 6.6 mm; Features:;;; Internal Optimize Power MOSFET; High efficiency up to 90%; Built in Frequency CompensationBuilt in Soft-Start Function; Built in Thermal Shutdown Function; Built in Current Limit Function;;;;; Note:; 1. Due to the diode partial pressure, the voltage of -Vo is lower than +Vo. 2. In order to obtain a more stable voltage, it is recommended that the output is greater than 15mA. 3. -Vo cannot be alone, or no voltage output. But you can just use +Vo.;;; Applications:;; ADC/DAC/Operational Amplifier; RS232 RS485 RS422 BusAudio equipmentLCD power supplyInstrumentation equipmentMCU BoardMotor PowerInstrumentation multimeterWifi/Router/Ethernet devices;;;; Attention:;;; 1. Input voltage can not be greater than the maximum input. 2. Output power can not be greater than the maximum load for a long time. 3. Input power must be greater than the output power, because the power consumption of the module itself.; Package Included:; 10 x DC 3.3 -13V to DC ±15V DC Step Up Voltage Converter Board;
2 Pcs Module: 1Pcs Bluetooth Wireless in the Form of Series Module Slave & 1Pcs MPU-6050 Module 3-Axis Analog Gyroscope
2 Pcs Module: 1Pcs Bluetooth module & 1Pcs MPU-6050 Module MPU-6050 module (3-axis gyro + 3 axis acceleration sensor) Power: 3-5v (internal low drop-out regulator) Communication mode: Standard IIC communication protocol chip, 16-bit integrated data output Gyro range: +/- 250 5001000 2000 / s Color: As shown Bluetooth module: Bluetooth wireless in the form of series module slave HC-06 3-axis gyro + 3 axis acceleration sensor: Immersion Gold PCB machine welding process pin 2.54 mm Acceleration range: +/- 8 +/- 2 +/- 4 16g Package Contents: 1 * Bluetooth module 1 * 3-axis gyro + 3 axis acceleration sensor Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
30pcs SX1308 DC-DC 2V-24V to 2V-28V 2A Adjustable Boost Regulated Power Supply Module High Current
Introduction:; The SX1308 boost module is equipped with the SX1308 chip, which has a small package and high efficiency. The output is adjustable up to 28V, and the internal integration of very low RDS internal resistance 100m & Omega; metal oxide semiconductor field effect transistor (MOSFET) can achieve high current output within 2A. Widely in 3G network products, digital products, mobile power, battery-powered equipment.; Features:; Oscillation frequency 1.2MH z, efficiency up to 95%The circuit has short circuit protection, overheat protection and other functions10K price potentiometer, adjust voltage output; Parameters:; Input voltage range: DC 2V-24VOutput voltage range: DC 2V-28VSwitching frequency: 1.2MH zOutput current: & le ; 2APackage includes: 30 x Power supply module
1.3 Inch SSD1106 I2C 128X64 OLED Display Module Board & GY-BMP280-3.3 Atmospheric Pressure Sensor Module
set 2: 1 x GY-BMP280- 3.3 Sensor Module + 1 x Module What is OLED? OLED (Organic Light-Emitting Diode) is a self light-emitting technology composed of a thin, multi-layered organic film placed between an anode and cathode. In contrast to LCD technology, OLED does not require a back light and therefore has much lower power usage. OLED possesses high application potential for virtually all types of displays and is regarded as the ultimate technology for the next generation of flat-panel displays. Self-emitting light, does not need a back light High luminosity Because pressure changes with altitude, and the pressure measurements are so good, you can also use it as an altimeter with+/- 1 meter accuracy Low operating voltage and power consumption Quick response Wide range of operating temperatures (-40c to 85c) Specification Interface: I2C Resolution: 128 x 64 Driver IC: SSD1106 Arduino Library: U8g2 library Raspberry Pi Library: WiringPi Wiring Pi Pin Description: GND: Power Ground VCC: Power + (DC 3.3 ~5v) SCL: Clock Line SDA: Data Line escription: Model: GY-BMP280- 3.3 Chip: BMP280 Power supply: 3V Communication method: Standard IIC/SPI communication protocol Air pressure range: 300-1100hPa Pin pitch: 2.54 mm Module size: 11.5 mm x 15mm Color: purple/blue Material: Plastic Typical application: Enhancement of GPS navigation(e. g. time-to-first-fix improvement, dead-reckoning, slope detection) Indoor navigation(floor detection, elevator detection) Outdoor navigation, leisure and sports applications Weather forecast Health care application(e. g. sirometry) Vertical velocity indication(e. g. risk/sink speed) Package Contents: 1 x GY-BMP280- 3.3 Sensor Module 1 x pin header 1 x Module Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
10Pcs Dual USB Output 6-24V To 5.2V 3A DC-DC Step Down Power Charger Module Converter
Specification: 1. Model: usb1002 2. Name: Power Module 3. Features: Buck Charge 4. Product size: 33 * 33 * 8mm 5. Input voltage range: 6-24V 6. Output voltage: 5.2V (the output terminal is 5.3 - 5.4V, the load side is 5.1 - 5.2V ) 7. Output Current: 3A (without heat sink, the stability of the output current is 2A) 8. Compatible Phone Model: Andrews series, iPhone series, For Huawei, For Xiaomi, For... Note: 1. Input voltage can not exceed 24V, otherwise, it will cause damage to the device! 2. Enter the positive and negative can not be reversed, otherwise, it will cause damage to the device! Package Included: 10 x Dual USB Power Module
10pcs BESTEP 1 Channel 5V Relay Module 30A With Optocoupler Isolation Support High Low Level Trigger
Description:; The module adopts high quality 30A relay, and the maximum load is normally open interface: AC 250V/30A, DC 30V/30A; The chip optocoupler isolation, strong driving ability, stable performance, trigger current 5mA; Module working voltage: 5VCan be set up by high jumper or low level trigger. Fault-tolerant design, the relay will not operate even if the control line is disconnected. Power indicator (green), relay status indicator (red) The interface design is humanized, all interfaces can be directly connected through the terminals, so it is very convenient. Module size: 50mm x 33mm x 24mm (length * width * height) Product net weight: 36gThere are 4 fixed bolt holes, holes 3.1 mm, spacing 44.5 mm x 27.5 mmRelay version: 5VQuiescent current: 5mAMaximum current: 190mATrigger current: 2-4mA; Module interface description:; 1. DC+: module DC power supply positive pole (trigger terminal voltage positive). 2. DC-: module DC supply negative pole (trigger terminal voltage negative). 3. IN: signal trigger terminal (default trigger voltage is the same as power supply). 4. JD+: relay control terminal voltage positive pole5. JD-: relay control terminal voltage negative pole6. DC +/- and JD +/- uses jumper cap short connection, trigger terminal and relay control terminal voltage is the same. 7. Selection of high and low level trigger mode, when jumper is connected to L-terminal, IN-terminal is low level trigger, and H-terminal is high level trigger. 8. Normally closed terminal (NC): relay normally closed. 9. Public terminal (COM): common terminal of relay10. Normally open terminal (NO): relay normally open.; Package Included: 10 x 1 Channel 5V Relay Module
10pcs USB Boost Line Power Supply Module 5V To 12V Power Line 1A Power Cord
Description: & nbsp; Power to other devices by charging bank. Such as: routers, USB lights, USB fans, small LCD TVs, car purifiers, 5V speakers, etc. DC power plug size: diameter: 5.5 mm, diameter: 2.1 mm; inside is positive, the line length of 1 meter The USB input 5V voltage through the components, boost to 12V voltage 1A & nbsp; Package included: & nbsp; 10 x 5V To 12V Power Line
10pcs BESTEP 1 Channel 5V Relay Module 30A With Optocoupler Isolation Support High And Low Level Trigger
Description: & nbsp; The module adopts high quality 30A relay, and the maximum load is normally open interface: AC 250V/30A, DC 30V/30A; The chip optocoupler isolation, strong driving ability, stable performance, trigger current 5mA; Module working voltage: 5V Can be set up by high or low level trigger. Fault-tolerant design, the relay will not operate even if the control line is disconnected. Power indicator (green), relay status indicator (red) The interface design is humanized, all interfaces can be directly connected through the terminals, so it is very convenient. Module size: 50mm x 33mm x 24mm (length * width * height) Product net weight: 36g There are 4 fixed bolt holes, holes 3.1 mm, spacing 44.5 mm x 27.5 mm Relay version: 5V Quiescent current: 5mA Maximum current: 190mA Trigger current: 2-4mA & nbsp; Module interface description: & nbsp; 1. DC+: module DC power supply positive pole (trigger terminal voltage positive). 2. DC-: module DC supply negative pole (trigger terminal voltage negative). 3. IN: signal trigger terminal (default trigger voltage is the same as power supply). 4. JD+: relay control terminal voltage positive pole 5. JD-: relay control terminal voltage negative pole 6. DC +/- and JD +/- uses cap short connection, trigger terminal and relay control terminal voltage is the same. 7. Selection of high and low level trigger mode, when is connected to L-terminal, IN-terminal is low level trigger, and H-terminal is high level trigger. 8. Normally closed terminal (NC): relay normally closed. 9. Public terminal (COM): common terminal of relay 10. Normally open terminal (NO): relay normally open. & nbsp; Package Included: 10 x 1 Channel 5V Relay Module
10Pcs Dual USB Output 6-24V To 5.2V 3A DC-DC Step Down Power Charger Module Converter
Specification: 1. Model: usb1002 2. Name: Power Module 3. Features: Buck Charge 4. Product size: 33 * 33 * 8mm 5. Input voltage range: 6-24V 6. Output voltage: 5.2V (the output terminal is 5.3 - 5.4V, the load side is 5.1 - 5.2V ) 7. Output Current: 3A (without heat sink, the stability of the output current is 2A) 8. Compatible Phone Model: Andrews series, iPhone series, For Huawei, For Xiaomi, For Nokia... Note: 1. Input voltage can not exceed 24V, otherwise, it will cause damage to the device! 2. Enter the positive and negative can not be reversed, otherwise, it will cause damage to the device! Package Included: 10 x Dual USB Power Module
5 x HX711 Weighed Dual Channel Sensor 24 Bit Precision A / D module & 1x 0.96in I2C IIC Serial 128X64 OLED LCD Module
set 2: 1 x LED Display Module + 5 x Weighing Sensor AD Module Dual-channel 24-bit A / D Conversion HX711 Shieding This module uses 24 high precision A / D hx711 conversion chip, and has been designed for high precision electronic scale With two analogue channel inputs, the internal integration of a programmable gain amplifier 128. Input circuit can be configured to provide a bridge electric bridge voltage (such as pressure, weight), sensor model an Perfect high-end low-cost front-end sampling module Driving Chip: SSD1306 3. Interface Type: IIC 4. Pin Definition: GND, VCC, SCL, SDA colour: Photo Color Material: PC+ metal/ CCL Two selectable differential input channels Active Low-Noise On-chip PGA with selectable gain of 32, 64 and 128 On-chip power supply controller for load-cell and ADC analog power supply On-chip oscillator does not require external components with the optional external crystal On-chip power-on-reset Simple digital control and serial interface: pin-driven controls, no programming required Selectable 10SPS or 80SPS output data speed Simultaneous waste 50 and 60Hz Power consumption including on-chip analog supply controller: normal operation Less than 1.5 mA, switch off Less than 1uA Range of power supply voltages: 2.6 ~ 5.5V Operating temperature range: -40 ~ + 85 Centigrade Applicable Model: For Arduino Blue Yellow Word Light size: 0.96 inch Package Contents: 1 x LED Display Module 5 x Weighing Sensor AD Module Dual-channel 24-bit A / D Conversion HX711 Shieding Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
127Pcs Shrink Sleeving Tubing Tube Assortment Kit & 1 Pcs Resistance Detection Module Photosensitive Sensor
127Pcs Shrink Sleeving Tubing Tube Assortment Kit & 1 pcs Resistance Detection Module Features: with potentiometer adjustable tests adjustable brightness of the light Module instructions: 1. Photosensitive resistance module has the most sensitive ambient light, generally used for detecting environment immediate of the brightness of the module light, trigger SMC or relay, etc.; 2 brightness of ambient light module can not reach the threshold of setting, DO exit end of high-level, when light brightness of the external environment of the development of threshold, only to stop output low level; 3 output port can be directly connects to the single-chip minicomputer, through the single-chip minicomputer for detecting level up and down, so the change in intensity of the light of the test environment; 4 end of output can directly drive the relay module, which can form a light switch - operated. Heat Shrink Sleeving Kit: It shrinks to half its diameter. The game contains seven of the most popular sizes. Protect and isolate! Flame retardant perfect for professional, fast and safe use for the wire wrapping harness. Colour: Black Material: ABS Size: 10x6x3cm Module: 1 VCC positive power 3.3 - 5V supply 2 GND power is negative 3 exit switching TTL signal DO Working voltage of 3.3V - 5V Output form: Digital switching output (0 and 1) With fixed bolt hole, convenient installation Small circuit board prints: 3.2 cm x 1.4 cm The use of wide voltage comparator LM393 Colour: Blue Material: PCB Size: 3.2 cm x 1.4 cm Package Contents: 127 * Heat Shrink Sleeving Kit 1 * Module Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
RD6006/RD6006-W LED Switching Power Supply S-400W-48V/DC12V/24V/36V/60V 8.3A-33.3A Support Monitoring Transformer Lighting
Feature: Note: This power supply can be with Product ID: 1587151 (RD6006/RD6006-W),; S06A Case; Product ID; 1587330; (If you need to use with RD6006/RD6006-W, please select 60V)Model: S-400-xxOutput power: 400WOutput voltage: DC12/24/36/48/60V (Optional) Input voltage: 110V/220V ACAmbient temperature: -10 ° C ~ +50 ° CAdjustable voltage: & plusmn ; 10%Product size: 215 x 115 x 50mmItemTechnical SpecificationsOutputDC voltage12V24V36V48V60VRated current 33.3A 16.6A 11.1A 8.3A 6.6AR ated power 399.6W 398.4W 399.6W 398.4W 396WRipple and noise; ?
9-36V To 12V DC Buck Power Converter Waterproof Multiple Protection 3A Step Down Module Voltage Adapter for Car Alarms LED Car Display
Features:; 1. Thin, small size, high efficiency and easy to install. 2. Multiple protection: over current protection/over voltage protection/over high temperature/ short-circuit protection. 3. Purpose: car alarms, radio, intercom, electric motors, audio, navigation, surveillance, LED car display, air conditioning, fans, solar energy, DVD, LED lights, motors, pumps, and industrial electrical equipment, etc.; Specification:; Material: aluminumColor: silverShell size: 74x74x 32mm (LxWxH) Input voltage: DC12-24V (wide voltage: 9-36V)Output voltage: DC12VOutput current:; 3APower: 36WTransform efficiency: over 93%Ripple: 40MVPower consumption: 15MAWorking temp: -40 ? ~+ 85 ?Installation wire length: 13 -14cmWaterproof: IP67Input wire color: (+) Red, (-) Black. Output wire color: (+) Yellow, (-) Black. Note: Please be remind to make sure wiring carefully & correctly. No wiring reverses protection for this device. Package Included:; 1 x 9-36V To 12V DC Buck Power Converter Waterproof
Motor Speed Control Board, DC 10-50V 60A High Power Motor Speed Controller, PWM HHO RC Driver Controller Module with Switch, for Car Motor Speed Regulation, Etc
Product features:
?1.DC motor speed controller operating voltage range is DC 10-50V, max rated current is 60A, control power range is 0.01-3000W, working temperature range of -20?-40?.
?2. High-end Configuration: Our motor driver control board uses PWM modulation system to adjust light & speed. In addition, it is designed with radiators to doing heat dissipation created by MOS tube.
?3.Convenient Speed Control: With wires to connect potentiometer and regulation switch to control the speed, it is convenient to use.
?4.Low Quiescent Current: our speed regulation module is designed with low quiescent current 0.04A(When the working voltage is DC10V-50V, the quiescent current cannot exceed 40mA).
?5.Wide Application: our motor driver control board can be applied to universal DC brush motor speed regulation; car motor speed regulation; production line conveyor belt speed regulation; electronic fan speed regulation etc.
Package: 1xMotor Speed Control Board
50pcs SX1308 DC-DC 2V-24V to 2V-28V 2A Adjustable Boost Regulated Power Supply Module High Current
Introduction:; The SX1308 boost module is equipped with the SX1308 chip, which has a small package and high efficiency. The output is adjustable up to 28V, and the internal integration of very low RDS internal resistance 100m & Omega; metal oxide semiconductor field effect transistor (MOSFET) can achieve high current output within 2A. Widely in 3G network products, digital products, mobile power, battery-powered equipment.; Features:; Oscillation frequency 1.2MH z, efficiency up to 95%The circuit has short circuit protection, overheat protection and other functions10K price potentiometer, adjust voltage output; Parameters:; Input voltage range: DC 2V-24VOutput voltage range: DC 2V-28VSwitching frequency: 1.2MH zOutput current: & le ; 2APackage includes: 50 x Power supply module
DC-DC 3.5-30V to 4-30V Adjustable LM2587 Boost Voltage Regulator Step-up Power Converter Power Supply Transformer Module Board with High Power Terminal for Solar Panel Car Battery
Product Description Small size(38×52×20mm) and light weight (32g), portable and easy to install. Input voltage: DC 3.5 -30V; Output voltage: DC4-30V, please ensure that the output setting voltage is higher than input voltage. Maximum input current: 5A; Continuous working current: 3A. Adopts large encapsulation boost chip, high driving power and efficiency. Note: when you test, if the input voltage is higher than output voltage, please adjust the potentiometer clockwise, the output voltage will rise. Please Note: When you test if the output voltage is not higher than the input voltage. Please adjust potentiometer clockwise, the output voltage will rise, please do not adjust the counter-clockwise. in the case of high input voltage module would be damaged. Features: Input voltage range: 3.5V -30V (must ensure that the output setting voltage is higher than the input voltage) Output voltage range: 4.0V -30V Input maximum current: 5A (According to Power conservation Calculate the nominal conditions Output Current: Uin * Iin * efficiency = Uout * Iout) Continuous Current: 3A (ventilation and heat dissipation in good condition: Output voltage and input voltage ratio is not greater than 3) Package includes: 1x DC-DC Converter Module
10pcs DC 3.3-13V to DC 15V Positive Negative Dual Output Power Supply DC DC Step Up Boost Module Voltage Converter Board
Size ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size. Specifications:; Input voltage: DC 3.3 - 13VOutput voltage: DC ±15(Deviation is ±4%); Maximum input current: 1.8AM aximum output current: +Vo is 600mA, -Vo is 120mAQuiescent current: 3-4mADC DC Boost Converter Module working frequency 400kHz. Operating temperature;: -40~+125?Storage temperature;: -65~+150 ?Pin;: 2.54 mmSize: 25 x 16.3 x 6.6 mm; Features:;;; Internal Optimize Power MOSFET; High efficiency up to 90%; Built in Frequency CompensationBuilt in Soft-Start Function; Built in Thermal Shutdown Function; Built in Current Limit Function;;;;; Note:; 1. Due to the diode partial pressure, the voltage of -Vo is lower than +Vo. 2. In order to obtain a more stable voltage, it is recommended that the output is greater than 15mA. 3. -Vo cannot be alone, or no voltage output. But you can just use +Vo.;;; Applications:;; ADC/DAC/Operational Amplifier; RS232 RS485 RS422 BusAudio equipmentLCD power supplyInstrumentation equipmentMCU BoardMotor PowerInstrumentation multimeterWifi/Router/Ethernet devices;;;; Attention:;;; 1. Input voltage can not be greater than the maximum input. 2. Output power can not be greater than the maximum load for a long time. 3. Input power must be greater than the output power, because the power consumption of the module itself.; Package Included:; 10 x DC 3.3 -13V to DC ±15V DC Step Up Voltage Converter Board;
20 Sets EE25 3 with 3pin Transformer Bobbin PC40 Ferrite Core Vertical 40 Ferrite Halves and 20 Bobbin
Product descriptionKEY_TAB Widely used in color TV, monitor, electric car charger, DVD, switching power supply, UP power supply, DC-DC converter, high frequency transformer, filter, inductor, household appliance, industrial automation, instrumentation, communication, energy saving Lighting and more!KEY_TAB KEY_TAB Product Range: Transformers, filter inductors, coils, bobbins, magnetic cores.Type: EE25Pin spacing: 6mm/0.24''Row spacing: 13mm/0.5"Ferrite core Size: 25.5 x 6.5 x 10mm/1" x 0.2" x 0.4"(L*W*T)Bobbin size: 17 x 19 x 23mm/0.6" x 0.7" x 0.9"(L*W*H)Winding frame size: 10 x 9 x 9.5mm/0.4" x 0.35" x 0.3"(L*W*H)Package content: 20 SET =40 ferrite halves + 20 bobbin
30pcs 1300 : 8 Ohm Audio Transformer EE14 Transformateur Audio POS Transformador
Specifications: Model: EE14AC impedance: 1300:8 Size: about 13mm x 11mm x 6mmQuantity: 30pcsFrequency Type: High FrequencyThe spacing between the two needles is 5.0 mm, 0.7 mm rough for the pin. Package included: 30 x 1300:8 Audio Transformer
10 Sets EE16 5 with 5pin Transformer Bobbin PC40 Ferrite Core Vertical 20 Ferrite Halves and 10 Bobbin
Product descriptionKEY_TAB Widely used in color TV, monitor, electric car charger, DVD, switching power supply, UP power supply, DC-DC converter, high frequency transformer, filter, inductor, household appliance, industrial automation, instrumentation, communication, energy saving Lighting and more!KEY_TAB KEY_TAB Product Range: Transformers, filter inductors, coils, bobbins, magnetic cores.Type: EE16Pin spacing: 3mm/0.12''Row spacing: 10.5mm/0.4"Ferrite core Size: 17 x 4.5 x 7.5mm/0.6" x 0.2" x 0.3"(L*W*T)Bobbin size: 16 x 13.5 x 18mm/0.6" x 0.5" x 0.7"(L*W*H)Winding frame size: 8.5 x 6.5 x 5.5mm/0.3" x 0.2" x 0.2"(L*W*H)Package content: 10 SET = 20 ferrite halves + 10 bobbin
50pcs SX1308 DC-DC 2V-24V to 2V-28V 2A Adjustable Boost Regulated Power Supply Module High Current
Introduction:; The SX1308 boost module is equipped with the SX1308 chip, which has a small package and high efficiency. The output is adjustable up to 28V, and the internal integration of very low RDS internal resistance 100m & Omega; metal oxide semiconductor field effect transistor (MOSFET) can achieve high current output within 2A. Widely in 3G network products, digital products, mobile power, battery-powered equipment.; Features:; Oscillation frequency 1.2MH z, efficiency up to 95%The circuit has short circuit protection, overheat protection and other functions10K price potentiometer, adjust voltage output; Parameters:; Input voltage range: DC 2V-24VOutput voltage range: DC 2V-28VSwitching frequency: 1.2MH zOutput current: & le ; 2APackage includes: 50 x Power supply module
30pcs 1300 : 8 Ohm Audio Transformer EE14 Transformateur Audio POS Transformador
Specifications: Model: EE14AC impedance: 1300:8 Size: about 13mm x 11mm x 6mmQuantity: 30pcsFrequency Type: High FrequencyThe spacing between the two needles is 5.0 mm, 0.7 mm rough for the pin. Package included: 30 x 1300:8 Audio Transformer
30pcs SX1308 DC-DC 2V-24V to 2V-28V 2A Adjustable Boost Regulated Power Supply Module High Current
Introduction:; The SX1308 boost module is equipped with the SX1308 chip, which has a small package and high efficiency. The output is adjustable up to 28V, and the internal integration of very low RDS internal resistance 100m & Omega; metal oxide semiconductor field effect transistor (MOSFET) can achieve high current output within 2A. Widely in 3G network products, digital products, mobile power, battery-powered equipment.; Features:; Oscillation frequency 1.2MH z, efficiency up to 95%The circuit has short circuit protection, overheat protection and other functions10K price potentiometer, adjust voltage output; Parameters:; Input voltage range: DC 2V-24VOutput voltage range: DC 2V-28VSwitching frequency: 1.2MH zOutput current: & le ; 2APackage includes: 30 x Power supply module
1200W 20A DC Converter Boost Step Up Power Supply Module Input 10-60V Output 12-83V
Specifications:; Module name: 1200W boost constant current moduleModule properties: non isolated boost module (BOOST) Input voltage: 10-60VInput current: 20AQuiescent operating current: 15mAOutput voltage: 12-83V continuous adjustableOutput current: MAX 12A over 20A, please strengthen the; cooling (with input and output differential pressure, the greater; the pressure difference between the output current is small)Constant current range: 0.3 -20AOutput power: = input voltage; x 10AWorking temperature: -40~+85 degrees; Working frequency: 150KHzConversion efficiency: & le; 95% (efficiency and input, output voltage,; current, pressure difference)Installation: 4pcs 3mm columnConnection mode: welding output (please use big current and pure copper wire) Module size: 130mmx52mmx46mm (LxWxH); Feature:; 1. Over current protection: there is a certain range of error in the input over 30A,; automatically reducing the output voltage. 2. Short circuit protection: there is (input 40A fuse) double short circuit protection,; use more secure.; When using the boost power supply should pay attention to the following points:; 1. Input power supply voltage must be above 10V. 2. When the power supply is for the input power supply, the input power and; the output voltage of the input power supply are the first to be unloaded. Then pick; up the load. (must ensure that the switching power supply has been working). 3. When the constant current mode is to set the voltage, the constant voltage; must be higher than the input voltage. Do not use the way of short circuit output current,; the circuit structure of the boost module can not be adjusted in short circuit way. 4.; If the input voltage fluctuation range is lower than the set output voltage, then the output voltage is constant, it is to ensure that input is lower than the output voltage.; Package included:; 1 x 1200W boost constant current module
3pcs XL4015 5A High Power 75W DC-DC Adjustable Step Down Module LED Voltmeter Power Supply Module
Description: KEY_TAB This product is a 180 KHz fixed frequency PWM buck (step-down) DC/DC module, capable of driving a 5A load with high efficiency, low ripple and excellent line and load regulation. The module with a voltage meter to display the input voltage and output voltage, and the voltage can be corrected through the button to improve the accuracy of the voltmeter. KEY_TAB Features: KEY_TAB 1. LED power indicator. 2. Button to switch measurement of the input or output voltage, and LED indicates the current measurement of the input or output voltage; The nixie tube can be turned off by another button. Mentioned states are able to be memorized, is not lost even if the power is disconnected. (On-board marked "IN" LED is turned on, the nixie tube display input voltage value, "OUT" LED bright display is the output voltage value). 3. Special launch, the voltmeter calibration function, will never exist voltmeter inaccurate! Voltmeter calibration method: (1) Output voltage calibration steps Step 1, adjust the right button so that "OUT" LED lighted, the voltmeter shows the value of output voltage; Press the right button for more than 2 seconds, release, voltmeter and "OUT" LED flashes in synchronization so that you enter the output voltage calibration mode. Step 2, press the right button (normal speed), the voltage value is adding up a unit; Press the left button, minus a unit; Due to a is less than 0.1V, the minimum voltage display to 0.1V, so you need to continuously press 1-5 times to see the voltmeter change 0.1V, how many times voltmeter change 0.1V by pressing the key, depending on the current display voltage, the higher the voltage, the fewer the number of press. Step 3, press the right button for more than 2 seconds, release, to exit the output voltage calibration mode. All parameters set to automatically power down to save. (2) Input voltage calibration steps Step 1, adjust the right button so that "IN" LED lighted, the voltmeter shows the value of input voltage; press the right button for more than 2 seconds, release, voltmeter and "IN" LED flashes in synchronization so that you enter the input voltage calibration mode. Steps 2 and 3, consistent with the output voltage calibration method. KEY_TAB Specifications: KEY_TAB 1. Input voltage range: 4~38VDC(Note: input voltage not exceeding 38V) 2. Output voltage range: 1.25 -36VDC adjustable 3. Output current: 0-5A 4. Output power: 75W 5. voltmeter range: 4 to 40V, error & plusmn; 0.1V 6. Operating frequency: 180KHz 7. High efficiency up to 96% 8. Built in thermal shutdown function 9. Built in current limit function 10. Built in output short protection function 11. Input reverse polarity protection: None (if required, high current diode in series with the input). 12. L x W x H = 6.6 * 3.9 * 1.8CMKEY _TAB KEY_TAB Application: KEY_TAB The DC/DC buck module applications the input voltage is higher than the output voltage of the buck field, such as battery, power transformer, DIY adjustable regulated power supply, LCD Monitor and LCD TV, portable in
10Pcs Dual USB Output 6-24V To 5.2V 3A DC-DC Step Down Power Charger Module Converter
Specification: 1. Model: usb1002 2. Name: Power Module 3. Features: Buck Charge 4. Product size: 33 * 33 * 8mm 5. Input voltage range: 6-24V 6. Output voltage: 5.2V (the output terminal is 5.3 - 5.4V, the load side is 5.1 - 5.2V ) 7. Output Current: 3A (without heat sink, the stability of the output current is 2A) 8. Compatible Phone Model: Andrews series, iPhone series, For Huawei, For Xiaomi, For... Note: 1. Input voltage can not exceed 24V, otherwise, it will cause damage to the device! 2. Enter the positive and negative can not be reversed, otherwise, it will cause damage to the device! Package Included: 10 x Dual USB Power Module
2 M NTC Thermistor Temperature Sensor Waterproof Probe Wire 10 K 1% 3950 Black + Relay Module 2Piece Set
There is a stainless steel casing, waterproof. Measurement range: -20 to 105 degrees Celsius. Length: 2 m Measure ambient temperature. Heat-resistant Brand new and high quality. Can be used with Arduino Special Sensor Shield V 4.0 Be able to control various appliances and other equipments with large current Easy to be controlled by a lots of Microcontrollers like for Arduino, 8051, AVR, PIC, DSP, ARM, MSP Color: blue, Black material: metal + PCB board and electronic components Probe size: 5 x 25 mm Type: NTC 10K + /- 1% 3950 B constant: 3380 K - / + 1% Typical loss constant: 5 mW / degree C Insulation: Larger than 100 MOhm Peak voltage: 2 s, AC 1800 V 1 mA 2 s Size Name: 5V 2-Channel Dimension: Approx. 5x 3.8 x 1.7 cm Package Contents: 1 x NTC 10 K 1% 3950 Temperature Sensor 1 x 5V 2 channel relay module Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is + /- 1-3cm.
