close

Buy Pololu Products online in United States

Sort by
Pololu Jrk 12v12 USB Motor Controller with Feedback
Key Features: Versatile, general-purpose motor controller Designed to control many medium-sized DC brushed motors Two closed-loop feedback options: Analog voltage and tachometer (frequency) Supports four control interfaces: USB, TTL serial, analog voltage (potentiometer), and hobby radio control (RC) The powerful Jrk 12v12 motor controller is a highly configurable brushed DC motor controller that supports four interface modes: USB, logic-level serial, analog voltage, and hobby radio control (RC). The controller can be used as an open-loop speed control or for closed-loop speed or position control. The continuous output current is approximately 12 A (30 A max) and the operating range of 6 V to 16 V (with transient protection up to 40 V). Item Specifics 1 - Jrk 12v12 Controller 1 - 0.1" Male header 2 - 2-pin 5mm terminal blocks USB connectivity with emulated serial (COM) port allows direct motor control from a PC. Ultrasonic PWM to eliminate switching-induced motor shaft hum or whine. Robust, high-speed communication protocol with user-configurable error condition response. High internal resolution (12 bits) for smooth and flexible calibration to various input and feedback devices. Current sensing and limiting. Reversed power protection. Field-upgradeable firmware. Motor driver: VNH2SP30 Motor channels: 1 Operating voltage: 6 V to 16 V Continuous output current: 12 A Peak output current: 30 A Auto-detect baud rate range: 300 bps to 115, 200 bps Available fixed baud rates: 300 bps to 115, 200 bps Available PWM frequencies: 20 kHz, 5 kHz USB connector style: USB Mini-B Size: 1.35" x 1.85" Weight: 0.5 oz Some soldering may be required
Pololu
Pololu 5V Step-Up/Step-Down Voltage Regulator S7V7F5
Key Features: Input voltage: 2.7 V to 11.8 V Fixed 5V output with +5/-3% accuracy Typical continuous output current: 1 A when stepping down; 500 mA when stepping up Power-saving feature maintains high efficiency at low currents (quiescent current is less than 0.1 mA) Integrated over-temperature and short-circuit protection The Pololu step-up/step-down voltage regulator S7V7F5 is a switching regulator (also called a switched-mode power supply (SMPS) or DC-to-DC converter) that uses a buck-boost topology. It takes an input voltage from 2.7V to 11.8V and increases or decreases the voltage to a fixed 5V output with a typical efficiency of over 90%. This flexibility in input voltage is especially well-suited for battery-powered applications in which the battery voltage begins above 5 V and drops below as the battery discharges. Without the typical restriction on the battery voltage staying above the required voltage throughout its life, new battery packs and form factors can be considered. Item Specifics Minimum operating voltage: 2.7V Maximum operating voltage: 11.8V Maximum output current: 1A Output voltage: 5V Maximum quiescent current: 0.1 mA Size: 0.35 & Prime; & times; 0.475 & Prime; & times; 0.1 & Prime; Weight without headers: 0.6 g
Pololu
Pololu 5V, 9A Step-Down Voltage Regulator D24V90F5
Key Features: Generates a fixed 5 V output from input voltages up to 38 V Typical efficiency between 80% to 95% Integrated reverse-voltage protection, over-current and short-circuit protection, over-temperature shutoff, soft-start, and under-voltage lockout Typical maximum continuous output current between 4 A and 8 A This synchronous switching step-down (or buck) regulator takes an input voltage of up to 38 V and efficiently reduces it to 5 V with an available output current of around 9 A. Typical efficiencies of 80% to 95% make this regulator well suited for higher-power applications like powering motors or servos, while high efficiencies are maintained at light loads by dynamically changing the switching frequency, and an optional shutdown pin enables a low-power state with a current draw of a few hundred microamps. The regulator & rsquo; s output voltage setting can also be lowered by adding an external resistor. Item Specifics Size: 1.6 & Prime; & times; 0.8 & Prime; & times; 0.3 & Prime; Four 0.086 & Prime; mounting holes for #2 or M2 screws
Pololu
Pololu Force-Sensing Resistor: 0.6" Diameter Circle
Key Features: 0.72" dia. round - Flexible, light ( 0.25 g), and extremely thin ( 0.02 & Prime; ) Masked adhesive backing for easy mounting Compatible with most solderless breadboards and perfboards Force accuracy ranges from 5% to 25% This force-sensing resistor (FSR) from Interlink Electronics is a passive component that acts as a variable resistor, with resistance decreasing in response to increasing applied force, which makes it easy to add a touch interface to your project or create a robot with much more sophisticated tactile senses than are possible with simple lever switches. The polymer thick film (PTF) device is optimized for use in human touch control of electronic devices and can sense an applied force anywhere in the active area ranging from a few dozen grams to a few kilograms ( 0.2 N to 20 N). Item Specifics 1.7 & Prime; flexible leads Solder tab spacing: 0.1" Sensing area: 0.58" diameter Size: 1.72 & Prime; & times; 1.72 & Prime; & times; 0.02 & Prime; Weight: 0.25 g Not suitable for precision force measurements
Pololu
Pololu Simple High-Power Motor Controller 18v15 - Assembled
Key Features: Versatile, general-purpose motor controller Designed for brushed, DC motors Suitable for many motor control applications Supports four control interfaces: USB, TTL serial, analog voltage (potentiometer), and hobby radio control (RC) The Pololu Simple High-Power Motor Controller 18v15 makes basic control of brushed DC motors easy, with our free Simple Motor Control Center software enabling quick configuration over USB. The controller supports four interface modes: USB, TTL serial, analog voltage, and hobby radio control (RC). This version operates from 5.5 to 30 V and is efficient enough to deliver a continuous 15 A without a heat sink. Item Specifics 1 - High Power SMC 18v15 2 - 20x1 0.1" Male header (Pre-soldered) 2 - 4-pin 5mm terminal blocks (Pre-soldered) 1 - Blue shorting block (Pre-soldered) 1 - Power capacitor (Minimum recommended size) (Pre-soldered) Motor channels: 1 Control interface: USB; non-inverted TTL serial; RC servo pulses; analog voltage Minimum operating voltage: 5.5 V Maximum operating voltage: 30 V Continuous output current per channel: 15 A Maximum PWM frequency: 21.77 kHz Maximum logic voltage: 3.3 V Version: G2 24v12 (40 V max, 12 A max continuous) Size: 2.1 & Prime; & times; 1.1 & Prime; & times; 0.5 & Prime; Weight: 14 g
Pololu
Pololu Carrier with Sharp GP2Y0D810Z0F Digital Distance Sensor 10cm
Key Features: Small digital distance sensor Quick response time, small size, and low current draw Good choice for non-contact object detection Detection distances up to 10 mm This small digital distance sensor detects objects between 2 cm and 10 cm ( 0.8 & Prime; and 4 & Prime; ) away. With its quick response time, small size, and low current draw, this sensor is a good choice for non-contact object detection, and a compact carrier PCB makes it easy to integrate into your project. It consists of a Sharp GP2Y0D810 sensor module installed on a tiny carrier board, which includes all of the external components required to make them work. Item Specifics Sampling rate: 265-390 Hz Minimum operating voltage: 2.7 V Maximum operating voltage: 6.2 V Supply current: 5mA Output type: Digital Average current consumption: 5 mA (typical) Distance measuring range: 2 cm to 10 cm ( 0.8 & Prime; to 4 & Prime; ) Steady state update period: 2.56 ms typical ( 3.77 ms max) Size without header pins: 21.6 mm & times; 8.9 mm & times; 10.4 mm ( 0.85 & Prime; & times; 0.35 & Prime; & times; 0.41 & Prime; ) Weight without header pins: 1.5 g ( 0.05 oz)
Pololu
Pololu DRV8825 High Current Stepper Motor Driver Carrier
Key Features: Simple step and direction control interface Adjustable current control lets you set the maximum current output with a potentiometer Built-in regulator (no external logic voltage supply needed) Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout Short-to-ground and shorted-load protection This breakout board for TI & rsquo; s DRV8825 microstepping bipolar stepper motor driver features adjustable current limiting, over-current and over-temperature protection, and six microstep resolutions (down to 1/32-step). It operates from 8.2 V to 45 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (rated for up to 2.2 A per coil with sufficient additional cooling). The driver has a pinout and interface that are nearly identical to those of our A4988 stepper motor driver carriers, so it can be used as a higher-performance drop-in replacement for those boards in many applications. Item Specifics 1 - PCB 1 - 0.1" male header Minimum operating voltage: 8.2 V Maximum operating voltage: 45 V Continuous current per phase without heatsink: 1.5 A Maximum current per phase: 2.2 A Minimum logic voltage: 2.5 V Maximum logic voltage: 5.25 V Microstep resolutions: full, 1/2, 1/4, 1/8, 1/16, and 1/32 Size: 0.6 & Prime; & times; 0.8 Weight: 1.6 g Some soldering may be required
Pololu
Pololu Dual VNH5019 Motor Driver Shield (Arduino Compatible)
Key Features: Motor outputs can be combined to deliver up to 24 A continuous to a single motor Ultrasonic PWM operation up to 20 kHz Current sense voltage output proportional to motor current (only active while H-bridge is driving) Motor indicator LEDs show what the outputs are doing even when no motor is connected Arduino or Arduino clone compatible (through shield headers) or other microcontroller boards This shield makes it easy to control two high-power DC motors with your Arduino or Arduino-compatible board. Its dual robust VNH5019 motor drivers operate from 5.5 to 24 V and can deliver a continuous 12 A (30 A peak) per motor, or a continuous 24 A (60 A peak) to a single motor connected to both channels. These great drivers also offer current-sense feedback and accept ultrasonic PWM frequencies for quieter operation. The Arduino pin mappings can all be customized if the defaults are not convenient, and the motor driver control lines are broken out along the left side of the shield for general-purpose use without an Arduino. Item Specifics 1 - stackable 1 & times; 10 female header 2 - stackable 1 & times; 8 female headers 2 - stackable 1 & times; 6 female headers 3 - 5mm 2-pin terminal blocks 1 - male breakaway 40-pin 0.1 & Prime; straight header 1 - 0.1 & Prime; shorting block (for optionally supplying shield power to Arduino) Motor driver: VNH5019 Motor channels: 2 Minimum operating voltage: 5.5 V Maximum operating voltage: 24 V Continuous output current per channel: 12 A Peak output current per channel: 30 A Current sense: 0.14 V/A Maximum PWM frequency: 20 kHz Reverse voltage protection Size: 0.6 & Prime; & times; 0.8 Weight: 1.6 g Some soldering may be required Arduino is not included Not recommended for use with 24V batteries Connecting supplies over 16 V in reverse can damage the motor driver
Pololu
Pololu 3.3V, 500mA Step-Down Voltage Regulator D24V5F3
Key Features: Fixed 3.3 V output with 4% accuracy Typical efficiency of 80% to 93% 500 kHz switching frequency (when not in power-save mode) Over-current and short-circuit protection, over-temperature shutoff The compact ( 0.4" & times; 0.5" ) D24V5F3 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 3.3 V while allowing for a maximum output current of 500 mA. This regulator offers typical efficiencies between 80% and 90% and has a very low dropout, so it can be used with input voltages as low as a few hundred millivolts above 3.3 V. The pins have a 0.1" spacing, making this board compatible with standard solderless breadboards and perfboards. Item Specifics 1 - PCB 1 - 0.1" 4x1 straight header 1 - 0.1" 4x1 right angle header Minimum operating voltage: 3.4 V Maximum operating voltage: 36 V Maximum output current: 500 mA Output voltage: 3.3 V Maximum quiescent current: 0.2 mA Size: 0.5 & Prime; & times; 0.4 & Prime; & times; 0.1 & Prime; Weight without header pins: 0.6 g
Pololu
Pololu Jrk 21v3 USB Motor Controller with Feedback - Pre-soldered connectors
Key Features: Versatile, general-purpose motor controller Designed to control most small DC brushed motors Two closed-loop feedback options: Analog voltage and tachometer (frequency) Supports four control interfaces: USB, TTL serial, analog voltage (potentiometer), and hobby radio control (RC) The Jrk 21v3 motor controller is a highly configurable brushed DC motor controller that supports four interface modes: USB, logic-level serial, analog voltage, and hobby radio control (RC). The controller can be used with feedback for closed-loop speed or position control, or it can be used without feedback as an open-loop speed control. The continuous output current is approximately 3 A in the recommended operating range of 8 V to 28 V, with derated performance down to 5 V and transient protection to 40 V. Item Specifics 1 - Jrk 21v3 Controller 1 - 0.1" Male header (Pre-soldered) 2 - 2-pin 3.5 mm terminal blocks (Pre-soldered) USB connectivity with emulated serial (COM) port allows direct motor control from a PC. Ultrasonic PWM to eliminate switching-induced motor shaft hum or whine. Robust, high-speed communication protocol with user-configurable error condition response. High internal resolution (12 bits) for smooth and flexible calibration to various input and feedback devices. Current sensing and limiting. Reversed power protection. Field-upgradeable firmware. Motor driver: MC33926 Motor channels: 1 Operating voltage: 5 V to 28 V Continuous output current: 3 A Peak output current: 5 A Auto-detect baud rate range: 300 bps to 115, 200 bps Available fixed baud rates: 300 bps to 115, 200 bps Available PWM frequencies: 20 kHz, 5 kHz USB connector style: USB Mini-B Size: 1.35" x 1.35" x 0.5" Weight: 0.23 oz
Pololu
Pololu Jrk G2 21v3 USB Motor Controller with Feedback (Connectors Soldered)
Key Features: Easy open-loop or closed-loop control of one brushed DC motor with pre-soldered connections Supports five control interfaces: USB, TTL serial, I2C, analog voltage (potentiometer), and hobby radio control (RC) Free configuration software utility for Windows, Linux, and macOS Ultrasonic 20 kHz PWM for quieter operation (can be configured to use 5 kHz instead) Optional CRC error detection eliminates communication errors caused by noise or software faults This compact motor controller makes closed-loop speed or position (but not both! ) control of a brushed DC motor easy, with quick configuration over USB using our free software. It supports five control interfaces: USB, TTL serial, I & sup2; C, analog voltage (potentiometer), and hobby radio control (RC). This version offers a 4.5 V to 28 V operating range and can deliver continuous output currents up to 2.6 A (5 A peak) without a heat sink. This version ships with soldered header pins and terminal blocks. Item Specifics Size: 1.2 & Prime; & times; 1.0 & Prime; & times; 0.47 & Prime; Weight: 7.5 g Motor channels: 1 Control interface: USB; non-inverted TTL serial; I2C; RC servo pulses; analog voltage Minimum operating voltage: 4.5 V Maximum operating voltage: 28 V Continuous output current per channel: 2.6 A Maximum PWM frequency: 20 kHz Reverse voltage protection?: Y Version: G2 21v3 (28 V max, 2.6 A max continuous) Connectors soldered?: Y micro-B USB cable is required (not included)
Pololu
Back to Top