Citel MJ8-POE-B, PoE Protection, PoE-Protection Indoor
CITEL MJ8-POE-B GIGABIT ETHERNET POE SHIELDED SURGE ARRESTOR -DATA CLAMP VOLTAGE 7.5VDC POWER CLAMP VOLTAGE 60VDC - ALL CAT5 LEADS PROTECTED - UL APPROVED (NEW) The MJ8-POE is designed to protect sensitive data-processing equipment connected to a PoE (Power over Ethernet) network from transient overvoltages. The MJ8-POE surge protector is deployed in signal network applications with data transmission speeds of up to 1000 Mbps. The surge protector is housed in a shielded enclosure with high quality shielded RJ45 jacks. The transient protection circuit is based on high energy gas discharge tubes (GDT) and a network of fast response silicon avalanche diodes (SAD) to achieve sharp clamping of very large surge events. • 2 kA discharge capability • Shielded enclosure and connectors • IEC 61643-21 • UL479B • 10 Base T / 100 Base T / 1000 Base T compatible • Power clamp voltage: 60VDC • 650 mA • RJ45 Connectors
Citel - MTJ-DSL - Cylix Fused, RJ11, All Pins - MTJ Series
The MTJ Series of surge protectors for RJ45 and RJ11 interfaces will ensure the reliable operation of Local and Wide Area Networks. We offer protection for LAN interface technologies such as Ethernet 10/100/1000BASE T, and Power over Ethernet (PoE) applications. For WAN and Telco applications we offer protection for environments including ISDN, T1, FT1, DDS, analog dial up modems, faxes and more. Additionally, our Custom Products Division provides products for nonstandardd or custom applications not included in our standard product offering. The MTJ Series devices guard sensitive data networks against lightning induced surges, AC power interference, electrostatic discharge, and ground loop energies. Typical applications include: NICs, switches, hubs, repeaters, bridges, routers, point of sale terminals, modems, fax machines, telephones and most other types of communications equipment utilizing RJ45 or RJ11 modular telephone jacks. High speed avalanche diode technology is used in conjunction with low capacitance circuitry enabling the protectors to function at a much greater bandwidth without causing signal degradation. Standard units are available with up to 8 wires protected on the RJ45 devices, and up to 6 wires protected on the RJ11 device. All this, in combination with their small size, makes the MTJ series exceedingly versatile. NOTE: This is a general description please see title for actual product. State-of-the-art, avalanche diode and thyristor technology Compact, in-line installation High speed, high energy handling capability Low shunt capacitance to reduce signal loss STD. CLAMP VOLTAGE: 10BASE TRS422, RS423( 7.5 VOLTS), 100BASE T ETHERNET CAT 5/5E (12 VOLTS), 1000BASE T ETHERNET CAT 6( 7.5 VOLTS), POWER OVER ETHERNET (MODE A) (60 VOLTS), POWER OVER ETHERNET (MODE B) (Pins 1, 2, 3, & 6- 7.5 VOLTS Pins 4, 5, 7, & 8- 60 VOLTS), RS232 (18 VOLTS), DIGITAL, ISDN DDS, T1/E1 CSU/DSU, DSL (60 VOLTS), ANALOG/DIAL-UP/MODEM/FAX (240 VOLTS) PEAK PULSE CURRENT 10/1000 us s. c. waveform @Vcl: 10BASE TRS422, RS423 (132 AMPS), 100BASE T ETHERNET CAT 5/5E (97 AMPS), 1000BASE T ETHERNET CAT 6 (100 AMPS), POWER OVER ETHERNET (MODE A) (50 AMPS), POWER OVER ETHERNET (MODE B) (Pins 1, 2, 3, & 6 - 132 AMPS Pins 4, 5, 7, & 8- 50 AMPS), RS232 (60 AMPS), DIGITAL, ISDN DDS, T1/E1 CSU/DSU, DSL (50 AMPS), ANALOG/DIAL-UP/MODEM/FAX (75 AMPS) RESPONSE TIME: Less Than 5 Nanoseconds MAXIMUM SHUNT CAPACITANCE: 10BASE TRS422, RS423(
Citel - Ddp-h8-a - Cylix Arcnet, 8 Ports - All Pins, Rj45 - Ddp Series
The DDP Series of terminal strip protectors will ensure the reliable operation of networked equipment connected to RS422, RS232, Analog Dial Up, ISDN, T1 and most other communication interfaces. Transient surges can enter electronic equipment through any pathway provided. If a facility has a reliable AC power protection system in place, transient surge energies can still be generated within a building by sources such as inductive load switching, ground loop currents and electrostatic discharge. These surge energies are clamped by the AC power protector into the communication ground, damaging expensive communications hardware. Cylix protectors are specifically designed to give added security to electronic devices with extremely low tolerance for voltage rises or ground loop energies. This protection is particularly important for equipment networked at distances greater than 30 feet and installations in high lightning areas. DDP models protect virtually any communication interface including: 10BASE T and 100BASE T Ethernet, RS422, RS232, RS423 and most high speed LAN/WAN interfaces. Combined into a compact interface unit, the devices exhibit an extremely fast response time of less than 5 nanoseconds. All these features make DDP protectors the most cost effective and versatile devices of their kind available today. Whether you need to protect a single communication line, or an entire installation, Cylix DDP series protectors are an easy, cost-effective solution to overvoltage problems. NOTE: This is a general description please see title for actual product. State-of-the-art, avalanche diode technology Compact in-line installation High speed, high energy handling capability Low shunt capacitance to reduce signal loss Expandable design allowing for protection of up to 100 wires or 12 ports in a single package STD. CLAMP VOLTAGE: 10/100BASE TRS422, RS485, RS423(7.5 VOLTS), RS232(18 VOLTS), CSU/DSU NON SPAN T1(fused)(60 VOLTS), CSU/DSU NON SPAN T1 (Primary)(fused)(60 VOLTS), DIAL-UP/MODEM / FAX(fused)(240 VOLTS), DIAL-UP/MODEM / FAX (Primary)(fused)(240 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. waveform @Vcl: 10/100BASE TRS422, RS485, RS423(132 AMPS), RS232(60 AMPS), CSU/DSU NON SPAN T1(fused)(50 AMPS), CSU/DSU NON SPAN T1 (Primary)(fused)(100 AMPS), DIAL-UP/MODEM / FAX(fused)(75 AMPS), DIAL-UP/MODEM / FAX (Primary)(fused)(100 AMPS) RESPONSE TIME: Less Than 5 Nanoseconds MAXIMUM SHUNT CAPACITANCE: 10/100BASE TRS422, RS485, RS423(
Citel - MTJ-06G/RJ11 - Cylix MTJ-06G/RJ11 - RJ11, ALL PINS - MTJ Series
The MTJ Series of surge protectors for RJ45 and RJ11 interfaces will ensure the reliable operation of Local and Wide Area Networks. We offer protection for LAN interface technologies such as Ethernet 10/100/1000BASE T, and Power over Ethernet (PoE) applications. For WAN and Telco applications we offer protection for environments including ISDN, T1, FT1, DDS, analog dial up modems, faxes and more. Additionally, our Custom Products Division provides products for nonstandardd or custom applications not included in our standard product offering. The MTJ Series devices guard sensitive data networks against lightning induced surges, AC power interference, electrostatic discharge, and ground loop energies. Typical applications include: NICs, switches, hubs, repeaters, bridges, routers, point of sale terminals, modems, fax machines, telephones and most other types of communications equipment utilizing RJ45 or RJ11 modular telephone jacks. High speed avalanche diode technology is used in conjunction with low capacitance circuitry enabling the protectors to function at a much greater bandwidth without causing signal degradation. Standard units are available with up to 8 wires protected on the RJ45 devices, and up to 6 wires protected on the RJ11 device. All this, in combination with their small size, makes the MTJ series exceedingly versatile. NOTE: This is a general description please see title for actual product. State-of-the-art, avalanche diode and thyristor technology Compact, in-line installation High speed, high energy handling capability Low shunt capacitance to reduce signal loss STD. CLAMP VOLTAGE:10BASE TRS422, RS423(7.5 VOLTS), 100BASE T ETHERNET CAT 5/5E(12 VOLTS), 1000BASE T ETHERNET CAT 6(7.5 VOLTS), POWER OVER ETHERNET(MODE A)(60 VOLTS), POWER OVER ETHERNET(MODE B)(Pins 1, 2, 3, & 6- 7.5 VOLTSPins 4, 5, 7, & 8- 60 VOLTS), RS232(18 VOLTS), DIGITAL, ISDN DDS, T1/E1 CSU/DSU, DSL(60 VOLTS), ANALOG/DIAL-UP/MODEM/FAX(240 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. waveform @Vcl:10BASE TRS422, RS423(132 AMPS), 100BASE T ETHERNET CAT 5/5E(97 AMPS), 1000BASE T ETHERNET CAT 6(100 AMPS), POWER OVER ETHERNET(MODE A)(50 AMPS), POWER OVER ETHERNET(MODE B)(Pins 1, 2, 3, & 6 - 132 AMPS Pins 4, 5, 7, & 8- 50 AMPS), RS232(60 AMPS), DIGITAL, ISDN DDS, T1/E1 CSU/DSU, DSL(50 AMPS), ANALOG/DIAL-UP/MODEM/FAX(75 AMPS) RESPONSE TIME: Less Than 5 Nanoseconds MAXIMUM SHUNT CAPACITANCE: 10BASE TRS422, RS423(
Citel - MTJ-08E/RJ45 - Cylix MTJ-08E/RJ45 RJ45, All PINS - MTJ Series
The MTJ Series of surge protectors for RJ45 and RJ11 interfaces will ensure the reliable operation of Local and Wide Area Networks. We offer protection for LAN interface technologies such as Ethernet 10/100/1000BASE T, and Power over Ethernet (PoE) applications. For WAN and Telco applications we offer protection for environments including ISDN, T1, FT1, DDS, analog dial up modems, faxes and more. Additionally, our Custom Products Division provides products for nonstandardd or custom applications not included in our standard product offering. The MTJ Series devices guard sensitive data networks against lightning induced surges, AC power interference, electrostatic discharge, and ground loop energies. Typical applications include: NICs, switches, hubs, repeaters, bridges, routers, point of sale terminals, modems, fax machines, telephones and most other types of communications equipment utilizing RJ45 or RJ11 modular telephone jacks. High speed avalanche diode technology is used in conjunction with low capacitance circuitry enabling the protectors to function at a much greater bandwidth without causing signal degradation. Standard units are available with up to 8 wires protected on the RJ45 devices, and up to 6 wires protected on the RJ11 device. All this, in combination with their small size, makes the MTJ series exceedingly versatile. NOTE: This is a general description please see title for actual product. State-of-the-art, avalanche diode and thyristor technology Compact, in-line installation High speed, high energy handling capability Low shunt capacitance to reduce signal loss STD. CLAMP VOLTAGE: 10BASE TRS422, RS423( 7.5 VOLTS), 100BASE T ETHERNET CAT 5/5E (12 VOLTS), 1000BASE T ETHERNET CAT 6( 7.5 VOLTS), POWER OVER ETHERNET (MODE A) (60 VOLTS), POWER OVER ETHERNET (MODE B) (Pins 1, 2, 3, & 6- 7.5 VOLTS Pins 4, 5, 7, & 8- 60 VOLTS), RS232 (18 VOLTS), DIGITAL, ISDN DDS, T1/E1 CSU/DSU, DSL (60 VOLTS), ANALOG/DIAL-UP/MODEM/FAX (240 VOLTS) PEAK PULSE CURRENT 10/1000 us s. c. waveform @Vcl: 10BASE TRS422, RS423 (132 AMPS), 100BASE T ETHERNET CAT 5/5E (97 AMPS), 1000BASE T ETHERNET CAT 6 (100 AMPS), POWER OVER ETHERNET (MODE A) (50 AMPS), POWER OVER ETHERNET (MODE B) (Pins 1, 2, 3, & 6 - 132 AMPS Pins 4, 5, 7, & 8- 50 AMPS), RS232 (60 AMPS), DIGITAL, ISDN DDS, T1/E1 CSU/DSU, DSL (50 AMPS), ANALOG/DIAL-UP/MODEM/FAX (75 AMPS) RESPONSE TIME: Less Than 5 Nanoseconds MAXIMUM SHUNT CAPACITANCE: 10BASE TRS422, RS423(
Citel - MTJ-08A/RJ45 - Cylix MTJ-08A/RJ45 RJ45, All PINS - MTJ Series
The MTJ Series of surge protectors for RJ45 and RJ11 interfaces will ensure the reliable operation of Local and Wide Area Networks. We offer protection for LAN interface technologies such as Ethernet 10/100/1000BASE T, and Power over Ethernet (PoE) applications. For WAN and Telco applications we offer protection for environments including ISDN, T1, FT1, DDS, analog dial up modems, faxes and more. Additionally, our Custom Products Division provides products for nonstandardd or custom applications not included in our standard product offering. The MTJ Series devices guard sensitive data networks against lightning induced surges, AC power interference, electrostatic discharge, and ground loop energies. Typical applications include: NICs, switches, hubs, repeaters, bridges, routers, point of sale terminals, modems, fax machines, telephones and most other types of communications equipment utilizing RJ45 or RJ11 modular telephone jacks. High speed avalanche diode technology is used in conjunction with low capacitance circuitry enabling the protectors to function at a much greater bandwidth without causing signal degradation. Standard units are available with up to 8 wires protected on the RJ45 devices, and up to 6 wires protected on the RJ11 device. All this, in combination with their small size, makes the MTJ series exceedingly versatile. NOTE: This is a general description please see title for actual product. State-of-the-art, avalanche diode and thyristor technology Compact, in-line installation High speed, high energy handling capability Low shunt capacitance to reduce signal loss STD. CLAMP VOLTAGE:10BASE TRS422, RS423(7.5 VOLTS), 100BASE T ETHERNET CAT 5/5E(12 VOLTS), 1000BASE T ETHERNET CAT 6(7.5 VOLTS), POWER OVER ETHERNET(MODE A)(60 VOLTS), POWER OVER ETHERNET(MODE B)(Pins 1, 2, 3, & 6- 7.5 VOLTSPins 4, 5, 7, & 8- 60 VOLTS), RS232(18 VOLTS), DIGITAL, ISDN DDS, T1/E1 CSU/DSU, DSL(60 VOLTS), ANALOG/DIAL-UP/MODEM/FAX(240 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. waveform @Vcl:10BASE TRS422, RS423(132 AMPS), 100BASE T ETHERNET CAT 5/5E(97 AMPS), 1000BASE T ETHERNET CAT 6(100 AMPS), POWER OVER ETHERNET(MODE A)(50 AMPS), POWER OVER ETHERNET(MODE B)(Pins 1, 2, 3, & 6 - 132 AMPS Pins 4, 5, 7, & 8- 50 AMPS), RS232(60 AMPS), DIGITAL, ISDN DDS, T1/E1 CSU/DSU, DSL(50 AMPS), ANALOG/DIAL-UP/MODEM/FAX(75 AMPS) RESPONSE TIME: Less Than 5 Nanoseconds MAXIMUM SHUNT CAPACITANCE: 10BASE TRS422, RS423(
Citel - Mod-c6 - Cylix Cat 6, 2 Port Replacement Node - Pch Series
The PCH Series of Protected Patch Panels helps ensure the reliable operation of equipment utilizing CAT6/5e/5 Ethernet, 100/1000 Base T, T-1, ISDN, and telco protocols where system availability is absolutely critical. The PCH series is a 110 IDC to RJ45 patch panel with built-in surge protection. These devices help guard sensitive, high speed communication equipment from systems damage, data loss and down time resulting from the effects of lightening, surges, electrostatic discharge and other induced voltages on data lines. PCH units include industry-standard, 19?? rack-mounting for structured cabling environments, TIA/EIA CAT6 Standard compliance and an extremely fast response time of less than 5 nanoseconds. Convenient, built-in, all-wire protection makes this patch panel cost effective and a real time saver. Designed for high-speed data, voice and multimedia applications in structured cabling environments for mid to large-size business today, these units incorporate the latest in communication protection technology for mission critical installations. The self-resetting, 2000 Watt, bi-directional circuit provides maximum reliability. Over voltages are safely shunted to ground via an 11?? braided wire and chassis frame for maximum protection. NOTE: This is a general description please see title for actual product. State-of-the-art, avalanche diode and thyristor technology Self-resetting, 2000 Watt, bi-directional circuit Convenient, integral, wiring management system STD. CLAMP VOLTAGE: 100/1000BASE T CAT 6/5E/5 ETHERNET( 7.5 VOLTS), ISDN/T1/DDS (fused) (60 VOLTS), DIAL-UP/MODEM/FAX (fused) (240 VOLTS) PEAK PULSE CURRENT 10/1000 us s. c. waveform @Vcl: 100/1000BASE T CAT 6/5E/5 ETHERNET (100 AMPS), ISDN/T1/DDS (fused) (50 AMPS), DIAL-UP/MODEM/FAX (fused) (75 AMPS) RESPONSE TIME: Less Than 5 Nanoseconds MAXIMUM SHUNT CAPACITANCE: 100/1000BASE T CAT 6/5E/5 ETHERNET(
Citel - MTJ-08B/RJ45 - Cylix MTJ-08B/RJ45 RJ45, All PINS - MTJ Series
The MTJ Series of surge protectors for RJ45 and RJ11 interfaces will ensure the reliable operation of Local and Wide Area Networks. We offer protection for LAN interface technologies such as Ethernet 10/100/1000BASE T, and Power over Ethernet (PoE) applications. For WAN and Telco applications we offer protection for environments including ISDN, T1, FT1, DDS, analog dial up modems, faxes and more. Additionally, our Custom Products Division provides products for nonstandardd or custom applications not included in our standard product offering. The MTJ Series devices guard sensitive data networks against lightning induced surges, AC power interference, electrostatic discharge, and ground loop energies. Typical applications include: NICs, switches, hubs, repeaters, bridges, routers, point of sale terminals, modems, fax machines, telephones and most other types of communications equipment utilizing RJ45 or RJ11 modular telephone jacks. High speed avalanche diode technology is used in conjunction with low capacitance circuitry enabling the protectors to function at a much greater bandwidth without causing signal degradation. Standard units are available with up to 8 wires protected on the RJ45 devices, and up to 6 wires protected on the RJ11 device. All this, in combination with their small size, makes the MTJ series exceedingly versatile. NOTE: This is a general description please see title for actual product. State-of-the-art, avalanche diode and thyristor technology Compact, in-line installation High speed, high energy handling capability Low shunt capacitance to reduce signal loss STD. CLAMP VOLTAGE:10BASE TRS422, RS423(7.5 VOLTS), 100BASE T ETHERNET CAT 5/5E(12 VOLTS), 1000BASE T ETHERNET CAT 6(7.5 VOLTS), POWER OVER ETHERNET(MODE A)(60 VOLTS), POWER OVER ETHERNET(MODE B)(Pins 1, 2, 3, & 6- 7.5 VOLTSPins 4, 5, 7, & 8- 60 VOLTS), RS232(18 VOLTS), DIGITAL, ISDN DDS, T1/E1 CSU/DSU, DSL(60 VOLTS), ANALOG/DIAL-UP/MODEM/FAX(240 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. waveform @Vcl:10BASE TRS422, RS423(132 AMPS), 100BASE T ETHERNET CAT 5/5E(97 AMPS), 1000BASE T ETHERNET CAT 6(100 AMPS), POWER OVER ETHERNET(MODE A)(50 AMPS), POWER OVER ETHERNET(MODE B)(Pins 1, 2, 3, & 6 - 132 AMPS Pins 4, 5, 7, & 8- 50 AMPS), RS232(60 AMPS), DIGITAL, ISDN DDS, T1/E1 CSU/DSU, DSL(50 AMPS), ANALOG/DIAL-UP/MODEM/FAX(75 AMPS) RESPONSE TIME: Less Than 5 Nanoseconds MAXIMUM SHUNT CAPACITANCE: 10BASE TRS422, RS423(
Citel - Rak32-e-so - Cylix Rak32-e-so All Pins, Rj45, 32 Ports, With Standoff - Rak Series
The RAK series of Rack Mount and Wall Mount Standoff protectors will ensure the reliable operation of networked equipment connected to 10/100/1000BASE T Ethernet, RS422, RS232, Lease Line, Power over Ethernet (PoE), ISDN, T1, DDS, Dial-Up, and most other communication interfaces. Transient surges can enter electronic equipment through any pathway provided. Facilities with reliable AC power protectors can still experience surge-related, system downtime. Transient surge energies from sources such as inductive load switching, ground loop currents and electrostatic discharge are clamped by AC protectors into the shared communication ground, resulting in damage to expensive communications hardware. The RAK Series includes 16 port, 19 relay rack protectors as well as 16 and 32 port, 5 standoff units for wall mount protection or environments where 19 relay rack space is limited. A wide variety of communication interfaces are supported that include 10/100/1000BASE T Ethernet, RS232, RS422, Power over Ethernet (PoE) and high speed LAN/WAN applications. All these features make RAK protectors the most cost effective and versatile devices of their kind available today. Whether you need to protect a single network concentrator, or an entire relay rack full of voltage sensitive equipment, Cylix RAK series protectors are an easy, cost effective solution to overvoltage problems. NOTE: This is a general description please see title for acutal product. State-of-the-art, avalanche diode technology Compact in-line installation Easy, hot swappable, single ports High speed, high energy handling capability Low shunt capacitance to reduce signal loss Convenient Front Input and Output or Standoff bracket for the full data cabinets STD. CLAMP VOLTAGE: 10/100BASE T RS422, RS485, RS423, ETHERNET(7.5 VOLTS), 1000 BASE T CATEGORY 6 ETHERNET(7.5 VOLTS), HIGH VOLTAGE ETHERNET(60 VOLTS), RS232(18 VOLTS), T1(60 VOLTS), ISDN/DDS (fused)(60 VOLTS), DIAL-UP/MODEM/FAX(fused)(240 VOLTS), POWER OVER ETHERNET(MODE A)(60 VOLTS), POWER OVER ETHERNET(MODE B)(Pins 1, 2, 3, & 6 - 7.5 volts Pins 4, 5, 7, & 8 - 60 volts), CCTV(7.5 VOLTS), CABLE TV/SATELLITE(90 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. wave form @Vcl: 10/100BASE T RS422, RS485, RS423, ETHERNET(132 AMPS), 1000 BASE T CATEGORY 6 ETHERNET(100 AMPS), HIGH VOLTAGE ETHERNET(45 AMPS), RS232(60 AMPS), T1(50 AMPS), ISDN/DDS (fused)(50 AMPS), DIAL-UP/MODEM/FAX(fused)(75 AMPS), POWER OVER ETHERNET(MODE A)(50 AMPS), POWER OVER ETHERNET(MODE B)(Pins 1, 2, 3, & 6 - 132 amps Pins 4, 5, 7, & 8 - 50 amps), CCTV(132 AMPS), CABLE TV/SATELLITE(20ka(8/20 msec waveform)) RESPONSE TIME: Less than 5 nanoseconds MAXIMUM SHUNT CAPACITANCE: 10/100BASE T RS422, RS485, RS423, ETHERNET(
Citel - Ddp-h4-g - Cylix Telco Dial Up, 4 Ports - All Pins Rj45 - Ddp Series
The DDP Series of terminal strip protectors will ensure the reliable operation of networked equipment connected to RS422, RS232, Analog Dial Up, ISDN, T1 and most other communication interfaces. Transient surges can enter electronic equipment through any pathway provided. If a facility has a reliable AC power protection system in place, transient surge energies can still be generated within a building by sources such as inductive load switching, ground loop currents and electrostatic discharge. These surge energies are clamped by the AC power protector into the communication ground, damaging expensive communications hardware. Cylix protectors are specifically designed to give added security to electronic devices with extremely low tolerance for voltage rises or ground loop energies. This protection is particularly important for equipment networked at distances greater than 30 feet and installations in high lightning areas. DDP models protect virtually any communication interface including: 10BASE T and 100BASE T Ethernet, RS422, RS232, RS423 and most high speed LAN/WAN interfaces. Combined into a compact interface unit, the devices exhibit an extremely fast response time of less than 5 nanoseconds. All these features make DDP protectors the most cost effective and versatile devices of their kind available today. Whether you need to protect a single communication line, or an entire installation, Cylix DDP series protectors are an easy, cost-effective solution to overvoltage problems. NOTE: This is a general description please see title for actual product. State-of-the-art, avalanche diode technology Compact in-line installation High speed, high energy handling capability Low shunt capacitance to reduce signal loss Expandable design allowing for protection of up to 100 wires or 12 ports in a single package STD. CLAMP VOLTAGE: 10/100BASE TRS422, RS485, RS423(7.5 VOLTS), RS232(18 VOLTS), CSU/DSU NON SPAN T1(fused)(60 VOLTS), CSU/DSU NON SPAN T1 (Primary)(fused)(60 VOLTS), DIAL-UP/MODEM / FAX(fused)(240 VOLTS), DIAL-UP/MODEM / FAX (Primary)(fused)(240 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. waveform @Vcl: 10/100BASE TRS422, RS485, RS423(132 AMPS), RS232(60 AMPS), CSU/DSU NON SPAN T1(fused)(50 AMPS), CSU/DSU NON SPAN T1 (Primary)(fused)(100 AMPS), DIAL-UP/MODEM / FAX(fused)(75 AMPS), DIAL-UP/MODEM / FAX (Primary)(fused)(100 AMPS) RESPONSE TIME: Less Than 5 Nanoseconds MAXIMUM SHUNT CAPACITANCE: 10/100BASE TRS422, RS485, RS423(
Citel - DDP-25-A - Cylix DDP-25-A - 25 PAIRS , RJ21 M/F - DDP Series
The DDP Series of terminal strip protectors will ensure the reliable operation of networked equipment connected to RS422, RS232, Analog Dial Up, ISDN, T1 and most other communication interfaces. Transient surges can enter electronic equipment through any pathway provided. If a facility has a reliable AC power protection system in place, transient surge energies can still be generated within a building by sources such as inductive load switching, ground loop currents and electrostatic discharge. These surge energies are clamped by the AC power protector into the communication ground, damaging expensive communications hardware. Cylix protectors are specifically designed to give added security to electronic devices with extremely low tolerance for voltage rises or ground loop energies. This protection is particularly important for equipment networked at distances greater than 30 feet and installations in high lightning areas. DDP models protect virtually any communication interface including: 10BASE T and 100BASE T Ethernet, RS422, RS232, RS423 and most high speed LAN/WAN interfaces. Combined into a compact interface unit, the devices exhibit an extremely fast response time of less than 5 nanoseconds. All these features make DDP protectors the most cost effective and versatile devices of their kind available today. Whether you need to protect a single communication line, or an entire installation, Cylix DDP series protectors are an easy, cost-effective solution to overvoltage problems. NOTE: This is a general description please see title for actual product. State-of-the-art, avalanche diode technology Compact in-line installation High speed, high energy handling capability Low shunt capacitance to reduce signal loss Expandable design allowing for protection of up to 100 wires or 12 ports in a single package STD. CLAMP VOLTAGE: 10/100BASE TRS422, RS485, RS423(7.5 VOLTS), RS232(18 VOLTS), CSU/DSU NON SPAN T1(fused)(60 VOLTS), CSU/DSU NON SPAN T1 (Primary)(fused)(60 VOLTS), DIAL-UP/MODEM / FAX(fused)(240 VOLTS), DIAL-UP/MODEM / FAX (Primary)(fused)(240 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. waveform @Vcl: 10/100BASE TRS422, RS485, RS423(132 AMPS), RS232(60 AMPS), CSU/DSU NON SPAN T1(fused)(50 AMPS), CSU/DSU NON SPAN T1 (Primary)(fused)(100 AMPS), DIAL-UP/MODEM / FAX(fused)(75 AMPS), DIAL-UP/MODEM / FAX (Primary)(fused)(100 AMPS) RESPONSE TIME: Less Than 5 Nanoseconds MAXIMUM SHUNT CAPACITANCE: 10/100BASE TRS422, RS485, RS423(
Citel - Ccp-2da (an) - Cylix Ccp-2da (an) - 50 Arcnet, Bnc, M/f- Ccp Series
The CCP Series of data communication line surge protectors will ensure the reliable operation of coaxial based networking equipment running Ethernet, ArcNet, Satellite/Cable/Closed Circuit TV and most other wideband communication interfaces. The CCP Series devices guard sensitive data networks against lightning induced surges, AC power interference, electrostatic discharge and ground loop energies. Typical applications include: terminals, file servers, repeaters, and mainframes using Ethernet, security cameras and most other communication applications. High speed avalanche diode technology is used in conjunction with low capacitance circuitry enabling the protectors to function at a much greater bandwidth without causing signal degradation. This, in combination with their small size, makes the CCP exceedingly versatile. Standard units protect both center conductor(s) and shield circuits. A separate grounding wire on all units provides an isolated path to ground without adding an additional ground connection to the shield or network ground point. CCPs can also be specially configured to accommodate other standard connector interfaces (F, N, TNC, BNC, etc.). NOTE: This is a general description of this series please see title for actual product. State-of-the-art, avalanche diode technology Compact in-line installation High speed, high energy handling capability Low shunt capacitance to reduce signal loss STD. CLAMP VOLTAGE: ETHERNET(7.5 VOLTS), CCTV(7.5 VOLTS), CABLE/SATELLITE TV(90 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. waveform @Vcl: ETHERNET(132 AMPS), CCTV(132 AMPS), CABLE/SATELLITE TV(20 ka) RESPONSE TIME: Less than 5 nanoseconds MAXIMUM SHUNT CAPACITANCE: ETHERNET(
Citel - Mtj-isdn - Cylix 60v, Fused, Rj45, Isdn, 4 Center Pins - Mtj Series
The MTJ Series of surge protectors for RJ45 and RJ11 interfaces will ensure the reliable operation of Local and Wide Area Networks. We offer protection for LAN interface technologies such as Ethernet 10/100/1000BASE T, and Power over Ethernet (PoE) applications. For WAN and Telco applications we offer protection for environments including ISDN, T1, FT1, DDS, analog dial up modems, faxes and more. Additionally, our Custom Products Division provides products for nonstandardd or custom applications not included in our standard product offering. The MTJ Series devices guard sensitive data networks against lightning induced surges, AC power interference, electrostatic discharge, and ground loop energies. Typical applications include: NICs, switches, hubs, repeaters, bridges, routers, point of sale terminals, modems, fax machines, telephones and most other types of communications equipment utilizing RJ45 or RJ11 modular telephone jacks. High speed avalanche diode technology is used in conjunction with low capacitance circuitry enabling the protectors to function at a much greater bandwidth without causing signal degradation. Standard units are available with up to 8 wires protected on the RJ45 devices, and up to 6 wires protected on the RJ11 device. All this, in combination with their small size, makes the MTJ series exceedingly versatile. NOTE: This is a general description please see title for actual product. State-of-the-art, avalanche diode and thyristor technology Compact, in-line installation High speed, high energy handling capability Low shunt capacitance to reduce signal loss STD. CLAMP VOLTAGE:10BASE TRS422, RS423(7.5 VOLTS), 100BASE T ETHERNET CAT 5/5E(12 VOLTS), 1000BASE T ETHERNET CAT 6(7.5 VOLTS), POWER OVER ETHERNET(MODE A)(60 VOLTS), POWER OVER ETHERNET(MODE B)(Pins 1, 2, 3, & 6- 7.5 VOLTSPins 4, 5, 7, & 8- 60 VOLTS), RS232(18 VOLTS), DIGITAL, ISDN DDS, T1/E1 CSU/DSU, DSL(60 VOLTS), ANALOG/DIAL-UP/MODEM/FAX(240 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. waveform @Vcl:10BASE TRS422, RS423(132 AMPS), 100BASE T ETHERNET CAT 5/5E(97 AMPS), 1000BASE T ETHERNET CAT 6(100 AMPS), POWER OVER ETHERNET(MODE A)(50 AMPS), POWER OVER ETHERNET(MODE B)(Pins 1, 2, 3, & 6 - 132 AMPS Pins 4, 5, 7, & 8- 50 AMPS), RS232(60 AMPS), DIGITAL, ISDN DDS, T1/E1 CSU/DSU, DSL(50 AMPS), ANALOG/DIAL-UP/MODEM/FAX(75 AMPS) RESPONSE TIME: Less Than 5 Nanoseconds MAXIMUM SHUNT CAPACITANCE: 10BASE TRS422, RS423(
Citel - Tsp-8b-a - Cylix Tstsp-8b-a 8 Wire, Quick Connect, Terminal Block - Tsp Series
The TSP Series of terminal strip protectors will ensure the reliable operation of networked equipment connected to RS422, RS232, Analog Dial Up, ISDN, T1 and most other communication interfaces. The TSP Series devices will guard sensitive data networks against lightning induced surges, AC power interference, electrostatic discharge, and ground loop energies. Typical applications include: data communications and instrumentation interfaces using RS422, RS232, CSU/DSU, T1, PLC's and most other communication interfaces. When installed on the system I/O ports, TSPs prevent equipment damage and system errors which are a common result of transient surge energies induced onto the communications interface and ground plane. TSPs utilize low capacitance avalanche diode arrays for low loss, high speed protection. These field-proven circuits offer the most dependable protection available for today's highly sensitive electronic systems. Whether you need to protect a single communication line, or an entire installation, Cylix protectors are an easy, cost-effective solution to overvoltage problems. NOTE: This is a general description please see title for acutal product. State-of-the-art, avalanche diode technology Compact in-line installation High speed, high energy handling capability Low shunt capacitance to reduce signal loss STD. CLAMP VOLTAGE: 10BASE T ETHERNET(7.5 VOLTS), RS422, RS485, RS423(7.5 VOLTS), RS232 or DIGITAL 4-20 mA CURRENT LOOP(18 VOLTS), ANALOG 4-20 mA CURRENT LOOP(27 VOLTS), CSU/DSU T1, DDS, ISDN(fused)(60 VOLTS), DIAL-UP MODEM/FAX(fused)(240 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. waveform @Vcl: 10BASE T ETHERNET(132 AMPS), RS422, RS485, RS423(132 AMPS), RS232 or DIGITAL 4-20 mA CURRENT LOOP(60 AMPS), ANALOG 4-20 mA CURRENT LOOP(40 AMPS), CSU/DSU T1, DDS, ISDN(fused)(50 AMPS), DIAL-UP MODEM/FAX(fused)(75 AMPS) RESPONSE TIME: Less than 5 nanoseconds MAXIMUM SHUNT CAPACITANCE: 10BASE T ETHERNET(
Citel - Tsp-6b-a - Cylix Tsp-6b-a 6 Wire, Quick Connect, Terminal Block- Tsp Series
The TSP Series of terminal strip protectors will ensure the reliable operation of networked equipment connected to RS422, RS232, Analog Dial Up, ISDN, T1 and most other communication interfaces. The TSP Series devices will guard sensitive data networks against lightning induced surges, AC power interference, electrostatic discharge, and ground loop energies. Typical applications include: data communications and instrumentation interfaces using RS422, RS232, CSU/DSU, T1, PLC's and most other communication interfaces. When installed on the system I/O ports, TSPs prevent equipment damage and system errors which are a common result of transient surge energies induced onto the communications interface and ground plane. TSPs utilize low capacitance avalanche diode arrays for low loss, high speed protection. These field-proven circuits offer the most dependable protection available for today's highly sensitive electronic systems. Whether you need to protect a single communication line, or an entire installation, Cylix protectors are an easy, cost-effective solution to overvoltage problems. NOTE: This is a general description please see title for acutal product. State-of-the-art, avalanche diode technology Compact in-line installation High speed, high energy handling capability Low shunt capacitance to reduce signal loss STD. CLAMP VOLTAGE: 10BASE T ETHERNET(7.5 VOLTS), RS422, RS485, RS423(7.5 VOLTS), RS232 or DIGITAL 4-20 mA CURRENT LOOP(18 VOLTS), ANALOG 4-20 mA CURRENT LOOP(27 VOLTS), CSU/DSU T1, DDS, ISDN(fused)(60 VOLTS), DIAL-UP MODEM/FAX(fused)(240 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. waveform @Vcl: 10BASE T ETHERNET(132 AMPS), RS422, RS485, RS423(132 AMPS), RS232 or DIGITAL 4-20 mA CURRENT LOOP(60 AMPS), ANALOG 4-20 mA CURRENT LOOP(40 AMPS), CSU/DSU T1, DDS, ISDN(fused)(50 AMPS), DIAL-UP MODEM/FAX(fused)(75 AMPS) RESPONSE TIME: Less than 5 nanoseconds MAXIMUM SHUNT CAPACITANCE: 10BASE T ETHERNET(
Citel - DDP-25-E - Cylix DDP-25-E - 25 PAIRS , RJ21 M/F - DDP Series
The DDP Series of terminal strip protectors will ensure the reliable operation of networked equipment connected to RS422, RS232, Analog Dial Up, ISDN, T1 and most other communication interfaces. Transient surges can enter electronic equipment through any pathway provided. If a facility has a reliable AC power protection system in place, transient surge energies can still be generated within a building by sources such as inductive load switching, ground loop currents and electrostatic discharge. These surge energies are clamped by the AC power protector into the communication ground, damaging expensive communications hardware. Cylix protectors are specifically designed to give added security to electronic devices with extremely low tolerance for voltage rises or ground loop energies. This protection is particularly important for equipment networked at distances greater than 30 feet and installations in high lightning areas. DDP models protect virtually any communication interface including: 10BASE T and 100BASE T Ethernet, RS422, RS232, RS423 and most high speed LAN/WAN interfaces. Combined into a compact interface unit, the devices exhibit an extremely fast response time of less than 5 nanoseconds. All these features make DDP protectors the most cost effective and versatile devices of their kind available today. Whether you need to protect a single communication line, or an entire installation, Cylix DDP series protectors are an easy, cost-effective solution to overvoltage problems. NOTE: This is a general description please see title for actual product. State-of-the-art, avalanche diode technology Compact in-line installation High speed, high energy handling capability Low shunt capacitance to reduce signal loss Expandable design allowing for protection of up to 100 wires or 12 ports in a single package STD. CLAMP VOLTAGE: 10/100BASE TRS422, RS485, RS423( 7.5 VOLTS), RS232 (18 VOLTS), CSU/DSU NON SPAN T1 (fused) (60 VOLTS), CSU/DSU NON SPAN T1 (Primary) (fused) (60 VOLTS), DIAL-UP/MODEM / FAX (fused) (240 VOLTS), DIAL-UP/MODEM / FAX (Primary) (fused) (240 VOLTS) PEAK PULSE CURRENT 10/1000 us s. c. waveform @Vcl: 10/100BASE TRS422, RS485, RS423 (132 AMPS), RS232 (60 AMPS), CSU/DSU NON SPAN T1 (fused) (50 AMPS), CSU/DSU NON SPAN T1 (Primary) (fused) (100 AMPS), DIAL-UP/MODEM / FAX (fused) (75 AMPS), DIAL-UP/MODEM / FAX (Primary) (fused) (100 AMPS) RESPONSE TIME: Less Than 5 Nanoseconds MAXIMUM SHUNT CAPACITANCE: 10/100BASE TRS422, RS485, RS423(
Citel - DDP-25-B - Cylix DDP-25-B - 25 PAIRS , RJ21 M/F - DDP Series
The DDP Series of terminal strip protectors will ensure the reliable operation of networked equipment connected to RS422, RS232, Analog Dial Up, ISDN, T1 and most other communication interfaces. Transient surges can enter electronic equipment through any pathway provided. If a facility has a reliable AC power protection system in place, transient surge energies can still be generated within a building by sources such as inductive load switching, ground loop currents and electrostatic discharge. These surge energies are clamped by the AC power protector into the communication ground, damaging expensive communications hardware. Cylix protectors are specifically designed to give added security to electronic devices with extremely low tolerance for voltage rises or ground loop energies. This protection is particularly important for equipment networked at distances greater than 30 feet and installations in high lightning areas. DDP models protect virtually any communication interface including: 10BASE T and 100BASE T Ethernet, RS422, RS232, RS423 and most high speed LAN/WAN interfaces. Combined into a compact interface unit, the devices exhibit an extremely fast response time of less than 5 nanoseconds. All these features make DDP protectors the most cost effective and versatile devices of their kind available today. Whether you need to protect a single communication line, or an entire installation, Cylix DDP series protectors are an easy, cost-effective solution to overvoltage problems. NOTE: This is a general description please see title for actual product. State-of-the-art, avalanche diode technology Compact in-line installation High speed, high energy handling capability Low shunt capacitance to reduce signal loss Expandable design allowing for protection of up to 100 wires or 12 ports in a single package STD. CLAMP VOLTAGE: 10/100BASE TRS422, RS485, RS423(7.5 VOLTS), RS232(18 VOLTS), CSU/DSU NON SPAN T1(fused)(60 VOLTS), CSU/DSU NON SPAN T1 (Primary)(fused)(60 VOLTS), DIAL-UP/MODEM / FAX(fused)(240 VOLTS), DIAL-UP/MODEM / FAX (Primary)(fused)(240 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. waveform @Vcl: 10/100BASE TRS422, RS485, RS423(132 AMPS), RS232(60 AMPS), CSU/DSU NON SPAN T1(fused)(50 AMPS), CSU/DSU NON SPAN T1 (Primary)(fused)(100 AMPS), DIAL-UP/MODEM / FAX(fused)(75 AMPS), DIAL-UP/MODEM / FAX (Primary)(fused)(100 AMPS) RESPONSE TIME: Less Than 5 Nanoseconds MAXIMUM SHUNT CAPACITANCE: 10/100BASE TRS422, RS485, RS423(
Citel - Db15-rs232 - Cylix Db15-rs232 Db15, All Pins For Rs232 - Db-15 Sub Series - Sip Series
The SIP Series of Subminiature D interface protectors ensures the reliable operation of parallel and serial devices such as printers, and point-of-sale terminals, mainframes and most other devices using Subminiature D connectors, which are sensitive to destructive transient energies. Standard applications include Ethernet, Token Ring, RS232, RS422 and LAN/WAN interfaces. Special applications can be accommodated through our Custom Products Group. Transient surges can enter electronic equipment through any pathway provided and damage expensive communications hardware. If a facility has a reliable AC power protection system in place, transient surge energies can still be generated within a building by sources such as inductive load switching, ground loop currents and electrostatic discharge. SIP Series protectors combine compact enclosures with extremely fast response times of less than 5 nanoseconds. They are specifically designed to give added security to electronic devices sensitive to voltage rises or ground loop energies and have been particularly effective in areas prone to lightning activity. Subminiature D (9, 15, & 25 pin) interface connectors are available in configurations protecting all pins or specific pins as required. All these features make the SIP protectors the most cost effective and versatile devices of their kind available today. NOTE: This is a general description please see title for actual product. State-of-the-art, avalanche diode technology Compact in-line installation High speed, high energy handling capability Low shunt capacitance to reduce signal loss STD. CLAMP VOLTAGE: RS422/RS423/RS485(7.5 VOLTS), PARALLEL(7.5 VOLTS), RS232(18 VOLTS)
Citel - Rak32-g-so - Cylix Rak32-g-so 2 Center Pins, Rj45, 32 Ports, With Standoff - Rak Series
The RAK series of Rack Mount and Wall Mount Standoff protectors will ensure the reliable operation of networked equipment connected to 10/100/1000BASE T Ethernet, RS422, RS232, Lease Line, Power over Ethernet (PoE), ISDN, T1, DDS, Dial-Up, and most other communication interfaces. Transient surges can enter electronic equipment through any pathway provided. Facilities with reliable AC power protectors can still experience surge-related, system downtime. Transient surge energies from sources such as inductive load switching, ground loop currents and electrostatic discharge are clamped by AC protectors into the shared communication ground, resulting in damage to expensive communications hardware. The RAK Series includes 16 port, 19 relay rack protectors as well as 16 and 32 port, 5 standoff units for wall mount protection or environments where 19 relay rack space is limited. A wide variety of communication interfaces are supported that include 10/100/1000BASE T Ethernet, RS232, RS422, Power over Ethernet (PoE) and high speed LAN/WAN applications. All these features make RAK protectors the most cost effective and versatile devices of their kind available today. Whether you need to protect a single network concentrator, or an entire relay rack full of voltage sensitive equipment, Cylix RAK series protectors are an easy, cost effective solution to overvoltage problems. NOTE: This is a general description please see title for acutal product. State-of-the-art, avalanche diode technology Compact in-line installation Easy, hot swappable, single ports High speed, high energy handling capability Low shunt capacitance to reduce signal loss Convenient Front Input and Output or Standoff bracket for the full data cabinets STD. CLAMP VOLTAGE: 10/100BASE T RS422, RS485, RS423, ETHERNET(7.5 VOLTS), 1000 BASE T CATEGORY 6 ETHERNET(7.5 VOLTS), HIGH VOLTAGE ETHERNET(60 VOLTS), RS232(18 VOLTS), T1(60 VOLTS), ISDN/DDS (fused)(60 VOLTS), DIAL-UP/MODEM/FAX(fused)(240 VOLTS), POWER OVER ETHERNET(MODE A)(60 VOLTS), POWER OVER ETHERNET(MODE B)(Pins 1, 2, 3, & 6 - 7.5 volts Pins 4, 5, 7, & 8 - 60 volts), CCTV(7.5 VOLTS), CABLE TV/SATELLITE(90 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. wave form @Vcl: 10/100BASE T RS422, RS485, RS423, ETHERNET(132 AMPS), 1000 BASE T CATEGORY 6 ETHERNET(100 AMPS), HIGH VOLTAGE ETHERNET(45 AMPS), RS232(60 AMPS), T1(50 AMPS), ISDN/DDS (fused)(50 AMPS), DIAL-UP/MODEM/FAX(fused)(75 AMPS), POWER OVER ETHERNET(MODE A)(50 AMPS), POWER OVER ETHERNET(MODE B)(Pins 1, 2, 3, & 6 - 132 amps Pins 4, 5, 7, & 8 - 50 amps), CCTV(132 AMPS), CABLE TV/SATELLITE(20ka(8/20 msec waveform)) RESPONSE TIME: Less than 5 nanoseconds MAXIMUM SHUNT CAPACITANCE: 10/100BASE T RS422, RS485, RS423, ETHERNET(
Citel - Tsp-32b-b - Cylix Tsp-32b-b 32 Wire, Quick Connect, Terminal Block - Tsp Series
The TSP Series of terminal strip protectors will ensure the reliable operation of networked equipment connected to RS422, RS232, Analog Dial Up, ISDN, T1 and most other communication interfaces. The TSP Series devices will guard sensitive data networks against lightning induced surges, AC power interference, electrostatic discharge, and ground loop energies. Typical applications include: data communications and instrumentation interfaces using RS422, RS232, CSU/DSU, T1, PLC's and most other communication interfaces. When installed on the system I/O ports, TSPs prevent equipment damage and system errors which are a common result of transient surge energies induced onto the communications interface and ground plane. TSPs utilize low capacitance avalanche diode arrays for low loss, high speed protection. These field-proven circuits offer the most dependable protection available for today's highly sensitive electronic systems. Whether you need to protect a single communication line, or an entire installation, Cylix protectors are an easy, cost-effective solution to overvoltage problems. NOTE: This is a general description please see title for acutal product. State-of-the-art, avalanche diode technology Compact in-line installation High speed, high energy handling capability Low shunt capacitance to reduce signal loss STD. CLAMP VOLTAGE: 10BASE T ETHERNET(7.5 VOLTS), RS422, RS485, RS423(7.5 VOLTS), RS232 or DIGITAL 4-20 mA CURRENT LOOP(18 VOLTS), ANALOG 4-20 mA CURRENT LOOP(27 VOLTS), CSU/DSU T1, DDS, ISDN(fused)(60 VOLTS), DIAL-UP MODEM/FAX(fused)(240 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. waveform @Vcl: 10BASE T ETHERNET(132 AMPS), RS422, RS485, RS423(132 AMPS), RS232 or DIGITAL 4-20 mA CURRENT LOOP(60 AMPS), ANALOG 4-20 mA CURRENT LOOP(40 AMPS), CSU/DSU T1, DDS, ISDN(fused)(50 AMPS), DIAL-UP MODEM/FAX(fused)(75 AMPS) RESPONSE TIME: Less than 5 nanoseconds MAXIMUM SHUNT CAPACITANCE: 10BASE T ETHERNET(
Citel - Tsp-8b-e - Cylix Tsp-8b-e 8 Wire, Quick Connect, Terminal Block - Tsp Series
The TSP Series of terminal strip protectors will ensure the reliable operation of networked equipment connected to RS422, RS232, Analog Dial Up, ISDN, T1 and most other communication interfaces. The TSP Series devices will guard sensitive data networks against lightning induced surges, AC power interference, electrostatic discharge, and ground loop energies. Typical applications include: data communications and instrumentation interfaces using RS422, RS232, CSU/DSU, T1, PLC's and most other communication interfaces. When installed on the system I/O ports, TSPs prevent equipment damage and system errors which are a common result of transient surge energies induced onto the communications interface and ground plane. TSPs utilize low capacitance avalanche diode arrays for low loss, high speed protection. These field-proven circuits offer the most dependable protection available for today's highly sensitive electronic systems. Whether you need to protect a single communication line, or an entire installation, Cylix protectors are an easy, cost-effective solution to overvoltage problems. NOTE: This is a general description please see title for acutal product. State-of-the-art, avalanche diode technology Compact in-line installation High speed, high energy handling capability Low shunt capacitance to reduce signal loss STD. CLAMP VOLTAGE: 10BASE T ETHERNET(7.5 VOLTS), RS422, RS485, RS423(7.5 VOLTS), RS232 or DIGITAL 4-20 mA CURRENT LOOP(18 VOLTS), ANALOG 4-20 mA CURRENT LOOP(27 VOLTS), CSU/DSU T1, DDS, ISDN(fused)(60 VOLTS), DIAL-UP MODEM/FAX(fused)(240 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. waveform @Vcl: 10BASE T ETHERNET(132 AMPS), RS422, RS485, RS423(132 AMPS), RS232 or DIGITAL 4-20 mA CURRENT LOOP(60 AMPS), ANALOG 4-20 mA CURRENT LOOP(40 AMPS), CSU/DSU T1, DDS, ISDN(fused)(50 AMPS), DIAL-UP MODEM/FAX(fused)(75 AMPS) RESPONSE TIME: Less than 5 nanoseconds MAXIMUM SHUNT CAPACITANCE: 10BASE T ETHERNET(
Citel - Tsp-8b-g - Cylix Tsp-8b-g 8 Wire, Quick Connect, Terminal Block - Tsp Series
The TSP Series of terminal strip protectors will ensure the reliable operation of networked equipment connected to RS422, RS232, Analog Dial Up, ISDN, T1 and most other communication interfaces. The TSP Series devices will guard sensitive data networks against lightning induced surges, AC power interference, electrostatic discharge, and ground loop energies. Typical applications include: data communications and instrumentation interfaces using RS422, RS232, CSU/DSU, T1, PLC's and most other communication interfaces. When installed on the system I/O ports, TSPs prevent equipment damage and system errors which are a common result of transient surge energies induced onto the communications interface and ground plane. TSPs utilize low capacitance avalanche diode arrays for low loss, high speed protection. These field-proven circuits offer the most dependable protection available for today's highly sensitive electronic systems. Whether you need to protect a single communication line, or an entire installation, Cylix protectors are an easy, cost-effective solution to overvoltage problems. NOTE: This is a general description please see title for acutal product. State-of-the-art, avalanche diode technology Compact in-line installation High speed, high energy handling capability Low shunt capacitance to reduce signal loss STD. CLAMP VOLTAGE: 10BASE T ETHERNET(7.5 VOLTS), RS422, RS485, RS423(7.5 VOLTS), RS232 or DIGITAL 4-20 mA CURRENT LOOP(18 VOLTS), ANALOG 4-20 mA CURRENT LOOP(27 VOLTS), CSU/DSU T1, DDS, ISDN(fused)(60 VOLTS), DIAL-UP MODEM/FAX(fused)(240 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. waveform @Vcl: 10BASE T ETHERNET(132 AMPS), RS422, RS485, RS423(132 AMPS), RS232 or DIGITAL 4-20 mA CURRENT LOOP(60 AMPS), ANALOG 4-20 mA CURRENT LOOP(40 AMPS), CSU/DSU T1, DDS, ISDN(fused)(50 AMPS), DIAL-UP MODEM/FAX(fused)(75 AMPS) RESPONSE TIME: Less than 5 nanoseconds MAXIMUM SHUNT CAPACITANCE: 10BASE T ETHERNET(
Citel - Tsp-32b-e - Cylix Tsp-32b-e 32 Wire, Quick Connect, Terminal Block - Tsp Series
The TSP Series of terminal strip protectors will ensure the reliable operation of networked equipment connected to RS422, RS232, Analog Dial Up, ISDN, T1 and most other communication interfaces. The TSP Series devices will guard sensitive data networks against lightning induced surges, AC power interference, electrostatic discharge, and ground loop energies. Typical applications include: data communications and instrumentation interfaces using RS422, RS232, CSU/DSU, T1, PLC's and most other communication interfaces. When installed on the system I/O ports, TSPs prevent equipment damage and system errors which are a common result of transient surge energies induced onto the communications interface and ground plane. TSPs utilize low capacitance avalanche diode arrays for low loss, high speed protection. These field-proven circuits offer the most dependable protection available for today's highly sensitive electronic systems. Whether you need to protect a single communication line, or an entire installation, Cylix protectors are an easy, cost-effective solution to overvoltage problems. NOTE: This is a general description please see title for acutal product. State-of-the-art, avalanche diode technology Compact in-line installation High speed, high energy handling capability Low shunt capacitance to reduce signal loss STD. CLAMP VOLTAGE: 10BASE T ETHERNET(7.5 VOLTS), RS422, RS485, RS423(7.5 VOLTS), RS232 or DIGITAL 4-20 mA CURRENT LOOP(18 VOLTS), ANALOG 4-20 mA CURRENT LOOP(27 VOLTS), CSU/DSU T1, DDS, ISDN(fused)(60 VOLTS), DIAL-UP MODEM/FAX(fused)(240 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. waveform @Vcl: 10BASE T ETHERNET(132 AMPS), RS422, RS485, RS423(132 AMPS), RS232 or DIGITAL 4-20 mA CURRENT LOOP(60 AMPS), ANALOG 4-20 mA CURRENT LOOP(40 AMPS), CSU/DSU T1, DDS, ISDN(fused)(50 AMPS), DIAL-UP MODEM/FAX(fused)(75 AMPS) RESPONSE TIME: Less than 5 nanoseconds MAXIMUM SHUNT CAPACITANCE: 10BASE T ETHERNET(
Citel - Tsp-6b-g - Cylix Tsp-6b-g 6 Wire, Quick Connect, Terminal Block- Tsp Series
The TSP Series of terminal strip protectors will ensure the reliable operation of networked equipment connected to RS422, RS232, Analog Dial Up, ISDN, T1 and most other communication interfaces. The TSP Series devices will guard sensitive data networks against lightning induced surges, AC power interference, electrostatic discharge, and ground loop energies. Typical applications include: data communications and instrumentation interfaces using RS422, RS232, CSU/DSU, T1, PLC's and most other communication interfaces. When installed on the system I/O ports, TSPs prevent equipment damage and system errors which are a common result of transient surge energies induced onto the communications interface and ground plane. TSPs utilize low capacitance avalanche diode arrays for low loss, high speed protection. These field-proven circuits offer the most dependable protection available for today's highly sensitive electronic systems. Whether you need to protect a single communication line, or an entire installation, Cylix protectors are an easy, cost-effective solution to overvoltage problems. NOTE: This is a general description please see title for acutal product. State-of-the-art, avalanche diode technology Compact in-line installation High speed, high energy handling capability Low shunt capacitance to reduce signal loss STD. CLAMP VOLTAGE: 10BASE T ETHERNET(7.5 VOLTS), RS422, RS485, RS423(7.5 VOLTS), RS232 or DIGITAL 4-20 mA CURRENT LOOP(18 VOLTS), ANALOG 4-20 mA CURRENT LOOP(27 VOLTS), CSU/DSU T1, DDS, ISDN(fused)(60 VOLTS), DIAL-UP MODEM/FAX(fused)(240 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. waveform @Vcl: 10BASE T ETHERNET(132 AMPS), RS422, RS485, RS423(132 AMPS), RS232 or DIGITAL 4-20 mA CURRENT LOOP(60 AMPS), ANALOG 4-20 mA CURRENT LOOP(40 AMPS), CSU/DSU T1, DDS, ISDN(fused)(50 AMPS), DIAL-UP MODEM/FAX(fused)(75 AMPS) RESPONSE TIME: Less than 5 nanoseconds MAXIMUM SHUNT CAPACITANCE: 10BASE T ETHERNET(
Citel - Tsp-8b-t - Cylix Tsp-8b-t 8 Wire, Quick Connect, Terminal Block - Tsp Series
The TSP Series of terminal strip protectors will ensure the reliable operation of networked equipment connected to RS422, RS232, Analog Dial Up, ISDN, T1 and most other communication interfaces. The TSP Series devices will guard sensitive data networks against lightning induced surges, AC power interference, electrostatic discharge, and ground loop energies. Typical applications include: data communications and instrumentation interfaces using RS422, RS232, CSU/DSU, T1, PLC's and most other communication interfaces. When installed on the system I/O ports, TSPs prevent equipment damage and system errors which are a common result of transient surge energies induced onto the communications interface and ground plane. TSPs utilize low capacitance avalanche diode arrays for low loss, high speed protection. These field-proven circuits offer the most dependable protection available for today's highly sensitive electronic systems. Whether you need to protect a single communication line, or an entire installation, Cylix protectors are an easy, cost-effective solution to overvoltage problems. NOTE: This is a general description please see title for acutal product. State-of-the-art, avalanche diode technology Compact in-line installation High speed, high energy handling capability Low shunt capacitance to reduce signal loss STD. CLAMP VOLTAGE: 10BASE T ETHERNET(7.5 VOLTS), RS422, RS485, RS423(7.5 VOLTS), RS232 or DIGITAL 4-20 mA CURRENT LOOP(18 VOLTS), ANALOG 4-20 mA CURRENT LOOP(27 VOLTS), CSU/DSU T1, DDS, ISDN(fused)(60 VOLTS), DIAL-UP MODEM/FAX(fused)(240 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. waveform @Vcl: 10BASE T ETHERNET(132 AMPS), RS422, RS485, RS423(132 AMPS), RS232 or DIGITAL 4-20 mA CURRENT LOOP(60 AMPS), ANALOG 4-20 mA CURRENT LOOP(40 AMPS), CSU/DSU T1, DDS, ISDN(fused)(50 AMPS), DIAL-UP MODEM/FAX(fused)(75 AMPS) RESPONSE TIME: Less than 5 nanoseconds MAXIMUM SHUNT CAPACITANCE: 10BASE T ETHERNET(
Citel - Tsp-8b-b - Cylix Tsp-8b-b 8 Wire, Quick Connect, Terminal Block - Tsp Series
The TSP Series of terminal strip protectors will ensure the reliable operation of networked equipment connected to RS422, RS232, Analog Dial Up, ISDN, T1 and most other communication interfaces. The TSP Series devices will guard sensitive data networks against lightning induced surges, AC power interference, electrostatic discharge, and ground loop energies. Typical applications include: data communications and instrumentation interfaces using RS422, RS232, CSU/DSU, T1, PLC's and most other communication interfaces. When installed on the system I/O ports, TSPs prevent equipment damage and system errors which are a common result of transient surge energies induced onto the communications interface and ground plane. TSPs utilize low capacitance avalanche diode arrays for low loss, high speed protection. These field-proven circuits offer the most dependable protection available for today's highly sensitive electronic systems. Whether you need to protect a single communication line, or an entire installation, Cylix protectors are an easy, cost-effective solution to overvoltage problems. NOTE: This is a general description please see title for acutal product. State-of-the-art, avalanche diode technology Compact in-line installation High speed, high energy handling capability Low shunt capacitance to reduce signal loss STD. CLAMP VOLTAGE: 10BASE T ETHERNET(7.5 VOLTS), RS422, RS485, RS423(7.5 VOLTS), RS232 or DIGITAL 4-20 mA CURRENT LOOP(18 VOLTS), ANALOG 4-20 mA CURRENT LOOP(27 VOLTS), CSU/DSU T1, DDS, ISDN(fused)(60 VOLTS), DIAL-UP MODEM/FAX(fused)(240 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. waveform @Vcl: 10BASE T ETHERNET(132 AMPS), RS422, RS485, RS423(132 AMPS), RS232 or DIGITAL 4-20 mA CURRENT LOOP(60 AMPS), ANALOG 4-20 mA CURRENT LOOP(40 AMPS), CSU/DSU T1, DDS, ISDN(fused)(50 AMPS), DIAL-UP MODEM/FAX(fused)(75 AMPS) RESPONSE TIME: Less than 5 nanoseconds MAXIMUM SHUNT CAPACITANCE: 10BASE T ETHERNET(
Citel - DDP-H12-E - Cylix 10BASE T, RS422/RS423/RS485, 12 PORTS - ALL PINS, RJ45 - DDP Series
The DDP Series of terminal strip protectors will ensure the reliable operation of networked equipment connected to RS422, RS232, Analog Dial Up, ISDN, T1 and most other communication interfaces. Transient surges can enter electronic equipment through any pathway provided. If a facility has a reliable AC power protection system in place, transient surge energies can still be generated within a building by sources such as inductive load switching, ground loop currents and electrostatic discharge. These surge energies are clamped by the AC power protector into the communication ground, damaging expensive communications hardware. Cylix protectors are specifically designed to give added security to electronic devices with extremely low tolerance for voltage rises or ground loop energies. This protection is particularly important for equipment networked at distances greater than 30 feet and installations in high lightning areas. DDP models protect virtually any communication interface including: 10BASE T and 100BASE T Ethernet, RS422, RS232, RS423 and most high speed LAN/WAN interfaces. Combined into a compact interface unit, the devices exhibit an extremely fast response time of less than 5 nanoseconds. All these features make DDP protectors the most cost effective and versatile devices of their kind available today. Whether you need to protect a single communication line, or an entire installation, Cylix DDP series protectors are an easy, cost-effective solution to overvoltage problems. NOTE: This is a general description please see title for actual product. State-of-the-art, avalanche diode technology Compact in-line installation High speed, high energy handling capability Low shunt capacitance to reduce signal loss Expandable design allowing for protection of up to 100 wires or 12 ports in a single package STD. CLAMP VOLTAGE: 10/100BASE TRS422, RS485, RS423(7.5 VOLTS), RS232(18 VOLTS), CSU/DSU NON SPAN T1(fused)(60 VOLTS), CSU/DSU NON SPAN T1 (Primary)(fused)(60 VOLTS), DIAL-UP/MODEM / FAX(fused)(240 VOLTS), DIAL-UP/MODEM / FAX (Primary)(fused)(240 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. waveform @Vcl: 10/100BASE TRS422, RS485, RS423(132 AMPS), RS232(60 AMPS), CSU/DSU NON SPAN T1(fused)(50 AMPS), CSU/DSU NON SPAN T1 (Primary)(fused)(100 AMPS), DIAL-UP/MODEM / FAX(fused)(75 AMPS), DIAL-UP/MODEM / FAX (Primary)(fused)(100 AMPS) RESPONSE TIME: Less Than 5 Nanoseconds MAXIMUM SHUNT CAPACITANCE: 10/100BASE TRS422, RS485, RS423(
Citel - Tsp-4b-t - Cylix Tsp-4b-t 4 Wire, Quick Connect, Terminal Block- Tsp Series
The TSP Series of terminal strip protectors will ensure the reliable operation of networked equipment connected to RS422, RS232, Analog Dial Up, ISDN, T1 and most other communication interfaces. The TSP Series devices will guard sensitive data networks against lightning induced surges, AC power interference, electrostatic discharge, and ground loop energies. Typical applications include: data communications and instrumentation interfaces using RS422, RS232, CSU/DSU, T1, PLC's and most other communication interfaces. When installed on the system I/O ports, TSPs prevent equipment damage and system errors which are a common result of transient surge energies induced onto the communications interface and ground plane. TSPs utilize low capacitance avalanche diode arrays for low loss, high speed protection. These field-proven circuits offer the most dependable protection available for today's highly sensitive electronic systems. Whether you need to protect a single communication line, or an entire installation, Cylix protectors are an easy, cost-effective solution to overvoltage problems. NOTE: This is a general description please see title for acutal product. State-of-the-art, avalanche diode technology Compact in-line installation High speed, high energy handling capability Low shunt capacitance to reduce signal loss STD. CLAMP VOLTAGE: 10BASE T ETHERNET(7.5 VOLTS), RS422, RS485, RS423(7.5 VOLTS), RS232 or DIGITAL 4-20 mA CURRENT LOOP(18 VOLTS), ANALOG 4-20 mA CURRENT LOOP(27 VOLTS), CSU/DSU T1, DDS, ISDN(fused)(60 VOLTS), DIAL-UP MODEM/FAX(fused)(240 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. waveform @Vcl: 10BASE T ETHERNET(132 AMPS), RS422, RS485, RS423(132 AMPS), RS232 or DIGITAL 4-20 mA CURRENT LOOP(60 AMPS), ANALOG 4-20 mA CURRENT LOOP(40 AMPS), CSU/DSU T1, DDS, ISDN(fused)(50 AMPS), DIAL-UP MODEM/FAX(fused)(75 AMPS) RESPONSE TIME: Less than 5 nanoseconds MAXIMUM SHUNT CAPACITANCE: 10BASE T ETHERNET(
Citel - Tsp-6b-b - Cylix Tsp-6b-b 6 Wire, Quick Connect, Terminal Block- Tsp Series
The TSP Series of terminal strip protectors will ensure the reliable operation of networked equipment connected to RS422, RS232, Analog Dial Up, ISDN, T1 and most other communication interfaces. The TSP Series devices will guard sensitive data networks against lightning induced surges, AC power interference, electrostatic discharge, and ground loop energies. Typical applications include: data communications and instrumentation interfaces using RS422, RS232, CSU/DSU, T1, PLC's and most other communication interfaces. When installed on the system I/O ports, TSPs prevent equipment damage and system errors which are a common result of transient surge energies induced onto the communications interface and ground plane. TSPs utilize low capacitance avalanche diode arrays for low loss, high speed protection. These field-proven circuits offer the most dependable protection available for today's highly sensitive electronic systems. Whether you need to protect a single communication line, or an entire installation, Cylix protectors are an easy, cost-effective solution to overvoltage problems. NOTE: This is a general description please see title for acutal product. State-of-the-art, avalanche diode technology Compact in-line installation High speed, high energy handling capability Low shunt capacitance to reduce signal loss STD. CLAMP VOLTAGE: 10BASE T ETHERNET(7.5 VOLTS), RS422, RS485, RS423(7.5 VOLTS), RS232 or DIGITAL 4-20 mA CURRENT LOOP(18 VOLTS), ANALOG 4-20 mA CURRENT LOOP(27 VOLTS), CSU/DSU T1, DDS, ISDN(fused)(60 VOLTS), DIAL-UP MODEM/FAX(fused)(240 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. waveform @Vcl: 10BASE T ETHERNET(132 AMPS), RS422, RS485, RS423(132 AMPS), RS232 or DIGITAL 4-20 mA CURRENT LOOP(60 AMPS), ANALOG 4-20 mA CURRENT LOOP(40 AMPS), CSU/DSU T1, DDS, ISDN(fused)(50 AMPS), DIAL-UP MODEM/FAX(fused)(75 AMPS) RESPONSE TIME: Less than 5 nanoseconds MAXIMUM SHUNT CAPACITANCE: 10BASE T ETHERNET(
Citel - Tsp-10b-t - Cylix Tsp-10b-t 10 Wire, Quick Connect, Terminal Block - Tsp Series
The TSP Series of terminal strip protectors will ensure the reliable operation of networked equipment connected to RS422, RS232, Analog Dial Up, ISDN, T1 and most other communication interfaces. The TSP Series devices will guard sensitive data networks against lightning induced surges, AC power interference, electrostatic discharge, and ground loop energies. Typical applications include: data communications and instrumentation interfaces using RS422, RS232, CSU/DSU, T1, PLC's and most other communication interfaces. When installed on the system I/O ports, TSPs prevent equipment damage and system errors which are a common result of transient surge energies induced onto the communications interface and ground plane. TSPs utilize low capacitance avalanche diode arrays for low loss, high speed protection. These field-proven circuits offer the most dependable protection available for today's highly sensitive electronic systems. Whether you need to protect a single communication line, or an entire installation, Cylix protectors are an easy, cost-effective solution to overvoltage problems. NOTE: This is a general description please see title for acutal product. State-of-the-art, avalanche diode technology Compact in-line installation High speed, high energy handling capability Low shunt capacitance to reduce signal loss STD. CLAMP VOLTAGE: 10BASE T ETHERNET(7.5 VOLTS), RS422, RS485, RS423(7.5 VOLTS), RS232 or DIGITAL 4-20 mA CURRENT LOOP(18 VOLTS), ANALOG 4-20 mA CURRENT LOOP(27 VOLTS), CSU/DSU T1, DDS, ISDN(fused)(60 VOLTS), DIAL-UP MODEM/FAX(fused)(240 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. waveform @Vcl: 10BASE T ETHERNET(132 AMPS), RS422, RS485, RS423(132 AMPS), RS232 or DIGITAL 4-20 mA CURRENT LOOP(60 AMPS), ANALOG 4-20 mA CURRENT LOOP(40 AMPS), CSU/DSU T1, DDS, ISDN(fused)(50 AMPS), DIAL-UP MODEM/FAX(fused)(75 AMPS) RESPONSE TIME: Less than 5 nanoseconds MAXIMUM SHUNT CAPACITANCE: 10BASE T ETHERNET(
Citel - DDP-50-B - Cylix DDP-50-B - 50 PAIRS, (2) RJ21 M/F - DDP Series
The DDP Series of terminal strip protectors will ensure the reliable operation of networked equipment connected to RS422, RS232, Analog Dial Up, ISDN, T1 and most other communication interfaces. Transient surges can enter electronic equipment through any pathway provided. If a facility has a reliable AC power protection system in place, transient surge energies can still be generated within a building by sources such as inductive load switching, ground loop currents and electrostatic discharge. These surge energies are clamped by the AC power protector into the communication ground, damaging expensive communications hardware. Cylix protectors are specifically designed to give added security to electronic devices with extremely low tolerance for voltage rises or ground loop energies. This protection is particularly important for equipment networked at distances greater than 30 feet and installations in high lightning areas. DDP models protect virtually any communication interface including: 10BASE T and 100BASE T Ethernet, RS422, RS232, RS423 and most high speed LAN/WAN interfaces. Combined into a compact interface unit, the devices exhibit an extremely fast response time of less than 5 nanoseconds. All these features make DDP protectors the most cost effective and versatile devices of their kind available today. Whether you need to protect a single communication line, or an entire installation, Cylix DDP series protectors are an easy, cost-effective solution to overvoltage problems. NOTE: This is a general description please see title for actual product. State-of-the-art, avalanche diode technology Compact in-line installation High speed, high energy handling capability Low shunt capacitance to reduce signal loss Expandable design allowing for protection of up to 100 wires or 12 ports in a single package STD. CLAMP VOLTAGE: 10/100BASE TRS422, RS485, RS423(7.5 VOLTS), RS232(18 VOLTS), CSU/DSU NON SPAN T1(fused)(60 VOLTS), CSU/DSU NON SPAN T1 (Primary)(fused)(60 VOLTS), DIAL-UP/MODEM / FAX(fused)(240 VOLTS), DIAL-UP/MODEM / FAX (Primary)(fused)(240 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. waveform @Vcl: 10/100BASE TRS422, RS485, RS423(132 AMPS), RS232(60 AMPS), CSU/DSU NON SPAN T1(fused)(50 AMPS), CSU/DSU NON SPAN T1 (Primary)(fused)(100 AMPS), DIAL-UP/MODEM / FAX(fused)(75 AMPS), DIAL-UP/MODEM / FAX (Primary)(fused)(100 AMPS) RESPONSE TIME: Less Than 5 Nanoseconds MAXIMUM SHUNT CAPACITANCE: 10/100BASE TRS422, RS485, RS423(
Citel - Rak16-bnc - Cylix 16 Port 1u High Bnc Cctv Protector - Special Order Only - Contact Cylix For Availability - Rak
The RAK series of Rack Mount and Wall Mount Standoff protectors will ensure the reliable operation of networked equipment connected to 10/100/1000BASE T Ethernet, RS422, RS232, Lease Line, Power over Ethernet (PoE), ISDN, T1, DDS, Dial-Up, and most other communication interfaces. Transient surges can enter electronic equipment through any pathway provided. Facilities with reliable AC power protectors can still experience surge-related, system downtime. Transient surge energies from sources such as inductive load switching, ground loop currents and electrostatic discharge are clamped by AC protectors into the shared communication ground, resulting in damage to expensive communications hardware. The RAK Series includes 16 port, 19 relay rack protectors as well as 16 and 32 port, 5 standoff units for wall mount protection or environments where 19 relay rack space is limited. A wide variety of communication interfaces are supported that include 10/100/1000BASE T Ethernet, RS232, RS422, Power over Ethernet (PoE) and high speed LAN/WAN applications. All these features make RAK protectors the most cost effective and versatile devices of their kind available today. Whether you need to protect a single network concentrator, or an entire relay rack full of voltage sensitive equipment, Cylix RAK series protectors are an easy, cost effective solution to overvoltage problems. NOTE: This is a general description please see title for acutal product. State-of-the-art, avalanche diode technology Compact in-line installation Easy, hot swappable, single ports High speed, high energy handling capability Low shunt capacitance to reduce signal loss Convenient Front Input and Output or Standoff bracket for the full data cabinets STD. CLAMP VOLTAGE: 10/100BASE T RS422, RS485, RS423, ETHERNET( 7.5 VOLTS), 1000 BASE T CATEGORY 6 ETHERNET( 7.5 VOLTS), HIGH VOLTAGE ETHERNET (60 VOLTS), RS232 (18 VOLTS), T1 (60 VOLTS), ISDN/DDS (fused) (60 VOLTS), DIAL-UP/MODEM/FAX (fused) (240 VOLTS), POWER OVER ETHERNET (MODE A) (60 VOLTS), POWER OVER ETHERNET (MODE B) (Pins 1, 2, 3, & 6 - 7.5 volts Pins 4, 5, 7, & 8 - 60 volts), CCTV( 7.5 VOLTS), CABLE TV/SATELLITE (90 VOLTS) PEAK PULSE CURRENT 10/1000 us s. c. wave form @Vcl: 10/100BASE T RS422, RS485, RS423, ETHERNET (132 AMPS), 1000 BASE T CATEGORY 6 ETHERNET (100 AMPS), HIGH VOLTAGE ETHERNET (45 AMPS), RS232 (60 AMPS), T1 (50 AMPS), ISDN/DDS (fused) (50 AMPS), DIAL-UP/MODEM/FAX (fused) (75 AMPS), POWER OVER ETHERNET (MODE A) (50 AMPS), POWER OVER ETHERNET (MODE B) (Pins 1, 2, 3, & 6 - 132 amps Pins 4, 5, 7, & 8 - 50 amps), CCTV (132 AMPS), CABLE TV/SATELLITE(20ka(8/20 msec waveform)) RESPONSE TIME: Less than 5 nanoseconds MAXIMUM SHUNT CAPACITANCE: 10/100BASE T RS422, RS485, RS423, ETHERNET(
Citel - Tsp-2b-e - Cylix Tsp-2b-e 2 Center Wire, Quick Connect, Terminal Block- Tsp Series
The TSP Series of terminal strip protectors will ensure the reliable operation of networked equipment connected to RS422, RS232, Analog Dial Up, ISDN, T1 and most other communication interfaces. The TSP Series devices will guard sensitive data networks against lightning induced surges, AC power interference, electrostatic discharge, and ground loop energies. Typical applications include: data communications and instrumentation interfaces using RS422, RS232, CSU/DSU, T1, PLC's and most other communication interfaces. When installed on the system I/O ports, TSPs prevent equipment damage and system errors which are a common result of transient surge energies induced onto the communications interface and ground plane. TSPs utilize low capacitance avalanche diode arrays for low loss, high speed protection. These field-proven circuits offer the most dependable protection available for today's highly sensitive electronic systems. Whether you need to protect a single communication line, or an entire installation, Cylix protectors are an easy, cost-effective solution to overvoltage problems. NOTE: This is a general description please see title for acutal product. State-of-the-art, avalanche diode technology Compact in-line installation High speed, high energy handling capability Low shunt capacitance to reduce signal loss STD. CLAMP VOLTAGE: 10BASE T ETHERNET(7.5 VOLTS), RS422, RS485, RS423(7.5 VOLTS), RS232 or DIGITAL 4-20 mA CURRENT LOOP(18 VOLTS), ANALOG 4-20 mA CURRENT LOOP(27 VOLTS), CSU/DSU T1, DDS, ISDN(fused)(60 VOLTS), DIAL-UP MODEM/FAX(fused)(240 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. waveform @Vcl: 10BASE T ETHERNET(132 AMPS), RS422, RS485, RS423(132 AMPS), RS232 or DIGITAL 4-20 mA CURRENT LOOP(60 AMPS), ANALOG 4-20 mA CURRENT LOOP(40 AMPS), CSU/DSU T1, DDS, ISDN(fused)(50 AMPS), DIAL-UP MODEM/FAX(fused)(75 AMPS) RESPONSE TIME: Less than 5 nanoseconds MAXIMUM SHUNT CAPACITANCE: 10BASE T ETHERNET(
Citel - Tsp-2b-b - Cylix Tsp-2b-b 2 Center Wire, Quick Connect, Terminal Block- Tsp Series
The TSP Series of terminal strip protectors will ensure the reliable operation of networked equipment connected to RS422, RS232, Analog Dial Up, ISDN, T1 and most other communication interfaces. The TSP Series devices will guard sensitive data networks against lightning induced surges, AC power interference, electrostatic discharge, and ground loop energies. Typical applications include: data communications and instrumentation interfaces using RS422, RS232, CSU/DSU, T1, PLC's and most other communication interfaces. When installed on the system I/O ports, TSPs prevent equipment damage and system errors which are a common result of transient surge energies induced onto the communications interface and ground plane. TSPs utilize low capacitance avalanche diode arrays for low loss, high speed protection. These field-proven circuits offer the most dependable protection available for today's highly sensitive electronic systems. Whether you need to protect a single communication line, or an entire installation, Cylix protectors are an easy, cost-effective solution to overvoltage problems. NOTE: This is a general description please see title for acutal product. State-of-the-art, avalanche diode technology Compact in-line installation High speed, high energy handling capability Low shunt capacitance to reduce signal loss STD. CLAMP VOLTAGE: 10BASE T ETHERNET(7.5 VOLTS), RS422, RS485, RS423(7.5 VOLTS), RS232 or DIGITAL 4-20 mA CURRENT LOOP(18 VOLTS), ANALOG 4-20 mA CURRENT LOOP(27 VOLTS), CSU/DSU T1, DDS, ISDN(fused)(60 VOLTS), DIAL-UP MODEM/FAX(fused)(240 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. waveform @Vcl: 10BASE T ETHERNET(132 AMPS), RS422, RS485, RS423(132 AMPS), RS232 or DIGITAL 4-20 mA CURRENT LOOP(60 AMPS), ANALOG 4-20 mA CURRENT LOOP(40 AMPS), CSU/DSU T1, DDS, ISDN(fused)(50 AMPS), DIAL-UP MODEM/FAX(fused)(75 AMPS) RESPONSE TIME: Less than 5 nanoseconds MAXIMUM SHUNT CAPACITANCE: 10BASE T ETHERNET(
Citel - Tsp-2b-t - Cylix Tsp-2b-t 2 Center Wire, Quick Connect, Terminal Block - Tsp Series
The TSP Series of terminal strip protectors will ensure the reliable operation of networked equipment connected to RS422, RS232, Analog Dial Up, ISDN, T1 and most other communication interfaces. The TSP Series devices will guard sensitive data networks against lightning induced surges, AC power interference, electrostatic discharge, and ground loop energies. Typical applications include: data communications and instrumentation interfaces using RS422, RS232, CSU/DSU, T1, PLC's and most other communication interfaces. When installed on the system I/O ports, TSPs prevent equipment damage and system errors which are a common result of transient surge energies induced onto the communications interface and ground plane. TSPs utilize low capacitance avalanche diode arrays for low loss, high speed protection. These field-proven circuits offer the most dependable protection available for today's highly sensitive electronic systems. Whether you need to protect a single communication line, or an entire installation, Cylix protectors are an easy, cost-effective solution to overvoltage problems. NOTE: This is a general description please see title for acutal product. State-of-the-art, avalanche diode technology Compact in-line installation High speed, high energy handling capability Low shunt capacitance to reduce signal loss STD. CLAMP VOLTAGE: 10BASE T ETHERNET(7.5 VOLTS), RS422, RS485, RS423(7.5 VOLTS), RS232 or DIGITAL 4-20 mA CURRENT LOOP(18 VOLTS), ANALOG 4-20 mA CURRENT LOOP(27 VOLTS), CSU/DSU T1, DDS, ISDN(fused)(60 VOLTS), DIAL-UP MODEM/FAX(fused)(240 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. waveform @Vcl: 10BASE T ETHERNET(132 AMPS), RS422, RS485, RS423(132 AMPS), RS232 or DIGITAL 4-20 mA CURRENT LOOP(60 AMPS), ANALOG 4-20 mA CURRENT LOOP(40 AMPS), CSU/DSU T1, DDS, ISDN(fused)(50 AMPS), DIAL-UP MODEM/FAX(fused)(75 AMPS) RESPONSE TIME: Less than 5 nanoseconds MAXIMUM SHUNT CAPACITANCE: 10BASE T ETHERNET(
Citel - Pch12-rj45-g - Cylix 12 Port 110 Idc To Rj45 Telco - 4 Center Wires - Fused - Pch Series
The PCH Series of Protected Patch Panels helps ensure the reliable operation of equipment utilizing CAT6/5e/5 Ethernet, 100/1000 Base T, T-1, ISDN, and telco protocols where system availability is absolutely critical. The PCH series is a 110 IDC to RJ45 patch panel with built-in surge protection. These devices help guard sensitive, high speed communication equipment from systems damage, data loss and down time resulting from the effects of lightening, surges, electrostatic discharge and other induced voltages on data lines. PCH units include industry-standard, 19?? rack-mounting for structured cabling environments, TIA/EIA CAT6 Standard compliance and an extremely fast response time of less than 5 nanoseconds. Convenient, built-in, all-wire protection makes this patch panel cost effective and a real time saver. Designed for high-speed data, voice and multimedia applications in structured cabling environments for mid to large-size business today, these units incorporate the latest in communication protection technology for mission critical installations. The self-resetting, 2000 Watt, bi-directional circuit provides maximum reliability. Over voltages are safely shunted to ground via an 11?? braided wire and chassis frame for maximum protection. NOTE: This is a general description please see title for actual product. State-of-the-art, avalanche diode and thyristor technology Self-resetting, 2000 Watt, bi-directional circuit Convenient, integral, wiring management system STD. CLAMP VOLTAGE: 100/1000BASE T CAT 6/5E/5 ETHERNET(7.5 VOLTS), ISDN/T1/DDS(fused)(60 VOLTS), DIAL-UP/MODEM/FAX(fused)(240 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. waveform @Vcl: 100/1000BASE T CAT 6/5E/5 ETHERNET(100 AMPS), ISDN/T1/DDS(fused)(50 AMPS), DIAL-UP/MODEM/FAX(fused)(75 AMPS) RESPONSE TIME: Less Than 5 Nanoseconds MAXIMUM SHUNT CAPACITANCE: 100/1000BASE T CAT 6/5E/5 ETHERNET(
Citel - Rak-e-c5 - Cylix Rak-e-c5 100 Mhz (100base T, Etc.), All Pins, Rj45, Replacement Node- Rak Series
The RAK series of Rack Mount and Wall Mount Standoff protectors will ensure the reliable operation of networked equipment connected to 10/100/1000BASE T Ethernet, RS422, RS232, Lease Line, Power over Ethernet (PoE), ISDN, T1, DDS, Dial-Up, and most other communication interfaces. Transient surges can enter electronic equipment through any pathway provided. Facilities with reliable AC power protectors can still experience surge-related, system downtime. Transient surge energies from sources such as inductive load switching, ground loop currents and electrostatic discharge are clamped by AC protectors into the shared communication ground, resulting in damage to expensive communications hardware. The RAK Series includes 16 port, 19 relay rack protectors as well as 16 and 32 port, 5 standoff units for wall mount protection or environments where 19 relay rack space is limited. A wide variety of communication interfaces are supported that include 10/100/1000BASE T Ethernet, RS232, RS422, Power over Ethernet (PoE) and high speed LAN/WAN applications. All these features make RAK protectors the most cost effective and versatile devices of their kind available today. Whether you need to protect a single network concentrator, or an entire relay rack full of voltage sensitive equipment, Cylix RAK series protectors are an easy, cost effective solution to overvoltage problems. NOTE: This is a general description please see title for acutal product. State-of-the-art, avalanche diode technology Compact in-line installation Easy, hot swappable, single ports High speed, high energy handling capability Low shunt capacitance to reduce signal loss Convenient Front Input and Output or Standoff bracket for the full data cabinets STD. CLAMP VOLTAGE: 10/100BASE T RS422, RS485, RS423, ETHERNET(7.5 VOLTS), 1000 BASE T CATEGORY 6 ETHERNET(7.5 VOLTS), HIGH VOLTAGE ETHERNET(60 VOLTS), RS232(18 VOLTS), T1(60 VOLTS), ISDN/DDS (fused)(60 VOLTS), DIAL-UP/MODEM/FAX(fused)(240 VOLTS), POWER OVER ETHERNET(MODE A)(60 VOLTS), POWER OVER ETHERNET(MODE B)(Pins 1, 2, 3, & 6 - 7.5 volts Pins 4, 5, 7, & 8 - 60 volts), CCTV(7.5 VOLTS), CABLE TV/SATELLITE(90 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. wave form @Vcl: 10/100BASE T RS422, RS485, RS423, ETHERNET(132 AMPS), 1000 BASE T CATEGORY 6 ETHERNET(100 AMPS), HIGH VOLTAGE ETHERNET(45 AMPS), RS232(60 AMPS), T1(50 AMPS), ISDN/DDS (fused)(50 AMPS), DIAL-UP/MODEM/FAX(fused)(75 AMPS), POWER OVER ETHERNET(MODE A)(50 AMPS), POWER OVER ETHERNET(MODE B)(Pins 1, 2, 3, & 6 - 132 amps Pins 4, 5, 7, & 8 - 50 amps), CCTV(132 AMPS), CABLE TV/SATELLITE(20ka(8/20 msec waveform)) RESPONSE TIME: Less than 5 nanoseconds MAXIMUM SHUNT CAPACITANCE: 10/100BASE T RS422, RS485, RS423, ETHERNET(
Citel - Rak-e-c5-so - Cylix Rak-e-c5-so 100 Mhz (100base T, Etc.), All Pins, Rj45, Standoff Node - Rak Series
The RAK series of Rack Mount and Wall Mount Standoff protectors will ensure the reliable operation of networked equipment connected to 10/100/1000BASE T Ethernet, RS422, RS232, Lease Line, Power over Ethernet (PoE), ISDN, T1, DDS, Dial-Up, and most other communication interfaces. Transient surges can enter electronic equipment through any pathway provided. Facilities with reliable AC power protectors can still experience surge-related, system downtime. Transient surge energies from sources such as inductive load switching, ground loop currents and electrostatic discharge are clamped by AC protectors into the shared communication ground, resulting in damage to expensive communications hardware. The RAK Series includes 16 port, 19 relay rack protectors as well as 16 and 32 port, 5 standoff units for wall mount protection or environments where 19 relay rack space is limited. A wide variety of communication interfaces are supported that include 10/100/1000BASE T Ethernet, RS232, RS422, Power over Ethernet (PoE) and high speed LAN/WAN applications. All these features make RAK protectors the most cost effective and versatile devices of their kind available today. Whether you need to protect a single network concentrator, or an entire relay rack full of voltage sensitive equipment, Cylix RAK series protectors are an easy, cost effective solution to overvoltage problems. NOTE: This is a general description please see title for acutal product. State-of-the-art, avalanche diode technology Compact in-line installation Easy, hot swappable, single ports High speed, high energy handling capability Low shunt capacitance to reduce signal loss Convenient Front Input and Output or Standoff bracket for the full data cabinets STD. CLAMP VOLTAGE: 10/100BASE T RS422, RS485, RS423, ETHERNET(7.5 VOLTS), 1000 BASE T CATEGORY 6 ETHERNET(7.5 VOLTS), HIGH VOLTAGE ETHERNET(60 VOLTS), RS232(18 VOLTS), T1(60 VOLTS), ISDN/DDS (fused)(60 VOLTS), DIAL-UP/MODEM/FAX(fused)(240 VOLTS), POWER OVER ETHERNET(MODE A)(60 VOLTS), POWER OVER ETHERNET(MODE B)(Pins 1, 2, 3, & 6 - 7.5 volts Pins 4, 5, 7, & 8 - 60 volts), CCTV(7.5 VOLTS), CABLE TV/SATELLITE(90 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. wave form @Vcl: 10/100BASE T RS422, RS485, RS423, ETHERNET(132 AMPS), 1000 BASE T CATEGORY 6 ETHERNET(100 AMPS), HIGH VOLTAGE ETHERNET(45 AMPS), RS232(60 AMPS), T1(50 AMPS), ISDN/DDS (fused)(50 AMPS), DIAL-UP/MODEM/FAX(fused)(75 AMPS), POWER OVER ETHERNET(MODE A)(50 AMPS), POWER OVER ETHERNET(MODE B)(Pins 1, 2, 3, & 6 - 132 amps Pins 4, 5, 7, & 8 - 50 amps), CCTV(132 AMPS), CABLE TV/SATELLITE(20ka(8/20 msec waveform)) RESPONSE TIME: Less than 5 nanoseconds MAXIMUM SHUNT CAPACITANCE: 10/100BASE T RS422, RS485, RS423, ETHERNET(
Citel - Ccp-2da N (en) M/f - Cylix Ethernet 10base 5, 50 Ohm, N Type, M/f - Ccp Series
The CCP Series of data communication line surge protectors will ensure the reliable operation of coaxial based networking equipment running Ethernet, ArcNet, Satellite/Cable/Closed Circuit TV and most other wideband communication interfaces. The CCP Series devices guard sensitive data networks against lightning induced surges, AC power interference, electrostatic discharge and ground loop energies. Typical applications include: terminals, file servers, repeaters, and mainframes using Ethernet, security cameras and most other communication applications. High speed avalanche diode technology is used in conjunction with low capacitance circuitry enabling the protectors to function at a much greater bandwidth without causing signal degradation. This, in combination with their small size, makes the CCP exceedingly versatile. Standard units protect both center conductor(s) and shield circuits. A separate grounding wire on all units provides an isolated path to ground without adding an additional ground connection to the shield or network ground point. CCPs can also be specially configured to accommodate other standard connector interfaces (F, N, TNC, BNC, etc.). NOTE: This is a general description of this series please see title for actual product. State-of-the-art, avalanche diode technology Compact in-line installation High speed, high energy handling capability Low shunt capacitance to reduce signal loss STD. CLAMP VOLTAGE: ETHERNET(7.5 VOLTS), CCTV(7.5 VOLTS), CABLE/SATELLITE TV(90 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. waveform @Vcl: ETHERNET(132 AMPS), CCTV(132 AMPS), CABLE/SATELLITE TV(20 ka) RESPONSE TIME: Less than 5 nanoseconds MAXIMUM SHUNT CAPACITANCE: ETHERNET(
Citel - Ddp-25-b-hd - Cylix Ddp-25-b-hd - 25 Pairs, Rj21, M/f Heavy Duty Version - Ddp Series
The DDP Series of terminal strip protectors will ensure the reliable operation of networked equipment connected to RS422, RS232, Analog Dial Up, ISDN, T1 and most other communication interfaces. Transient surges can enter electronic equipment through any pathway provided. If a facility has a reliable AC power protection system in place, transient surge energies can still be generated within a building by sources such as inductive load switching, ground loop currents and electrostatic discharge. These surge energies are clamped by the AC power protector into the communication ground, damaging expensive communications hardware. Cylix protectors are specifically designed to give added security to electronic devices with extremely low tolerance for voltage rises or ground loop energies. This protection is particularly important for equipment networked at distances greater than 30 feet and installations in high lightning areas. DDP models protect virtually any communication interface including: 10BASE T and 100BASE T Ethernet, RS422, RS232, RS423 and most high speed LAN/WAN interfaces. Combined into a compact interface unit, the devices exhibit an extremely fast response time of less than 5 nanoseconds. All these features make DDP protectors the most cost effective and versatile devices of their kind available today. Whether you need to protect a single communication line, or an entire installation, Cylix DDP series protectors are an easy, cost-effective solution to overvoltage problems. NOTE: This is a general description please see title for actual product. State-of-the-art, avalanche diode technology Compact in-line installation High speed, high energy handling capability Low shunt capacitance to reduce signal loss Expandable design allowing for protection of up to 100 wires or 12 ports in a single package STD. CLAMP VOLTAGE: 10/100BASE TRS422, RS485, RS423(7.5 VOLTS), RS232(18 VOLTS), CSU/DSU NON SPAN T1(fused)(60 VOLTS), CSU/DSU NON SPAN T1 (Primary)(fused)(60 VOLTS), DIAL-UP/MODEM / FAX(fused)(240 VOLTS), DIAL-UP/MODEM / FAX (Primary)(fused)(240 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. waveform @Vcl: 10/100BASE TRS422, RS485, RS423(132 AMPS), RS232(60 AMPS), CSU/DSU NON SPAN T1(fused)(50 AMPS), CSU/DSU NON SPAN T1 (Primary)(fused)(100 AMPS), DIAL-UP/MODEM / FAX(fused)(75 AMPS), DIAL-UP/MODEM / FAX (Primary)(fused)(100 AMPS) RESPONSE TIME: Less Than 5 Nanoseconds MAXIMUM SHUNT CAPACITANCE: 10/100BASE TRS422, RS485, RS423(
Citel - Ddp-25-g-hd - Cylix Ddp-25-g-hd - 25 Pairs, Rj21, M/f Heavy Duty Version - Ddp Series
The DDP Series of terminal strip protectors will ensure the reliable operation of networked equipment connected to RS422, RS232, Analog Dial Up, ISDN, T1 and most other communication interfaces. Transient surges can enter electronic equipment through any pathway provided. If a facility has a reliable AC power protection system in place, transient surge energies can still be generated within a building by sources such as inductive load switching, ground loop currents and electrostatic discharge. These surge energies are clamped by the AC power protector into the communication ground, damaging expensive communications hardware. Cylix protectors are specifically designed to give added security to electronic devices with extremely low tolerance for voltage rises or ground loop energies. This protection is particularly important for equipment networked at distances greater than 30 feet and installations in high lightning areas. DDP models protect virtually any communication interface including: 10BASE T and 100BASE T Ethernet, RS422, RS232, RS423 and most high speed LAN/WAN interfaces. Combined into a compact interface unit, the devices exhibit an extremely fast response time of less than 5 nanoseconds. All these features make DDP protectors the most cost effective and versatile devices of their kind available today. Whether you need to protect a single communication line, or an entire installation, Cylix DDP series protectors are an easy, cost-effective solution to overvoltage problems. NOTE: This is a general description please see title for actual product. State-of-the-art, avalanche diode technology Compact in-line installation High speed, high energy handling capability Low shunt capacitance to reduce signal loss Expandable design allowing for protection of up to 100 wires or 12 ports in a single package STD. CLAMP VOLTAGE: 10/100BASE TRS422, RS485, RS423(7.5 VOLTS), RS232(18 VOLTS), CSU/DSU NON SPAN T1(fused)(60 VOLTS), CSU/DSU NON SPAN T1 (Primary)(fused)(60 VOLTS), DIAL-UP/MODEM / FAX(fused)(240 VOLTS), DIAL-UP/MODEM / FAX (Primary)(fused)(240 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. waveform @Vcl: 10/100BASE TRS422, RS485, RS423(132 AMPS), RS232(60 AMPS), CSU/DSU NON SPAN T1(fused)(50 AMPS), CSU/DSU NON SPAN T1 (Primary)(fused)(100 AMPS), DIAL-UP/MODEM / FAX(fused)(75 AMPS), DIAL-UP/MODEM / FAX (Primary)(fused)(100 AMPS) RESPONSE TIME: Less Than 5 Nanoseconds MAXIMUM SHUNT CAPACITANCE: 10/100BASE TRS422, RS485, RS423(
Citel - Rak32-e-c5-so - Cylix Rak32-e-c5-so 100 Mhz (100base T, Etc.) All Pins, Rj45, 32 Ports, W/standoff - Rak Series
The RAK series of Rack Mount and Wall Mount Standoff protectors will ensure the reliable operation of networked equipment connected to 10/100/1000BASE T Ethernet, RS422, RS232, Lease Line, Power over Ethernet (PoE), ISDN, T1, DDS, Dial-Up, and most other communication interfaces. Transient surges can enter electronic equipment through any pathway provided. Facilities with reliable AC power protectors can still experience surge-related, system downtime. Transient surge energies from sources such as inductive load switching, ground loop currents and electrostatic discharge are clamped by AC protectors into the shared communication ground, resulting in damage to expensive communications hardware. The RAK Series includes 16 port, 19 relay rack protectors as well as 16 and 32 port, 5 standoff units for wall mount protection or environments where 19 relay rack space is limited. A wide variety of communication interfaces are supported that include 10/100/1000BASE T Ethernet, RS232, RS422, Power over Ethernet (PoE) and high speed LAN/WAN applications. All these features make RAK protectors the most cost effective and versatile devices of their kind available today. Whether you need to protect a single network concentrator, or an entire relay rack full of voltage sensitive equipment, Cylix RAK series protectors are an easy, cost effective solution to overvoltage problems. NOTE: This is a general description please see title for acutal product. State-of-the-art, avalanche diode technology Compact in-line installation Easy, hot swappable, single ports High speed, high energy handling capability Low shunt capacitance to reduce signal loss Convenient Front Input and Output or Standoff bracket for the full data cabinets STD. CLAMP VOLTAGE: 10/100BASE T RS422, RS485, RS423, ETHERNET(7.5 VOLTS), 1000 BASE T CATEGORY 6 ETHERNET(7.5 VOLTS), HIGH VOLTAGE ETHERNET(60 VOLTS), RS232(18 VOLTS), T1(60 VOLTS), ISDN/DDS (fused)(60 VOLTS), DIAL-UP/MODEM/FAX(fused)(240 VOLTS), POWER OVER ETHERNET(MODE A)(60 VOLTS), POWER OVER ETHERNET(MODE B)(Pins 1, 2, 3, & 6 - 7.5 volts Pins 4, 5, 7, & 8 - 60 volts), CCTV(7.5 VOLTS), CABLE TV/SATELLITE(90 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. wave form @Vcl: 10/100BASE T RS422, RS485, RS423, ETHERNET(132 AMPS), 1000 BASE T CATEGORY 6 ETHERNET(100 AMPS), HIGH VOLTAGE ETHERNET(45 AMPS), RS232(60 AMPS), T1(50 AMPS), ISDN/DDS (fused)(50 AMPS), DIAL-UP/MODEM/FAX(fused)(75 AMPS), POWER OVER ETHERNET(MODE A)(50 AMPS), POWER OVER ETHERNET(MODE B)(Pins 1, 2, 3, & 6 - 132 amps Pins 4, 5, 7, & 8 - 50 amps), CCTV(132 AMPS), CABLE TV/SATELLITE(20ka(8/20 msec waveform)) RESPONSE TIME: Less than 5 nanoseconds MAXIMUM SHUNT CAPACITANCE: 10/100BASE T RS422, RS485, RS423, ETHERNET(
Citel - Rak16-e-c5-so - Cylix Rak16-e-c5-so 100 Mhz (100base T, Etc., All Pins, Rj45, 16 Ports, W/standoff - Rak Series
The RAK series of Rack Mount and Wall Mount Standoff protectors will ensure the reliable operation of networked equipment connected to 10/100/1000BASE T Ethernet, RS422, RS232, Lease Line, Power over Ethernet (PoE), ISDN, T1, DDS, Dial-Up, and most other communication interfaces. Transient surges can enter electronic equipment through any pathway provided. Facilities with reliable AC power protectors can still experience surge-related, system downtime. Transient surge energies from sources such as inductive load switching, ground loop currents and electrostatic discharge are clamped by AC protectors into the shared communication ground, resulting in damage to expensive communications hardware. The RAK Series includes 16 port, 19 relay rack protectors as well as 16 and 32 port, 5 standoff units for wall mount protection or environments where 19 relay rack space is limited. A wide variety of communication interfaces are supported that include 10/100/1000BASE T Ethernet, RS232, RS422, Power over Ethernet (PoE) and high speed LAN/WAN applications. All these features make RAK protectors the most cost effective and versatile devices of their kind available today. Whether you need to protect a single network concentrator, or an entire relay rack full of voltage sensitive equipment, Cylix RAK series protectors are an easy, cost effective solution to overvoltage problems. NOTE: This is a general description please see title for acutal product. State-of-the-art, avalanche diode technology Compact in-line installation Easy, hot swappable, single ports High speed, high energy handling capability Low shunt capacitance to reduce signal loss Convenient Front Input and Output or Standoff bracket for the full data cabinets STD. CLAMP VOLTAGE: 10/100BASE T RS422, RS485, RS423, ETHERNET(7.5 VOLTS), 1000 BASE T CATEGORY 6 ETHERNET(7.5 VOLTS), HIGH VOLTAGE ETHERNET(60 VOLTS), RS232(18 VOLTS), T1(60 VOLTS), ISDN/DDS (fused)(60 VOLTS), DIAL-UP/MODEM/FAX(fused)(240 VOLTS), POWER OVER ETHERNET(MODE A)(60 VOLTS), POWER OVER ETHERNET(MODE B)(Pins 1, 2, 3, & 6 - 7.5 volts Pins 4, 5, 7, & 8 - 60 volts), CCTV(7.5 VOLTS), CABLE TV/SATELLITE(90 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. wave form @Vcl: 10/100BASE T RS422, RS485, RS423, ETHERNET(132 AMPS), 1000 BASE T CATEGORY 6 ETHERNET(100 AMPS), HIGH VOLTAGE ETHERNET(45 AMPS), RS232(60 AMPS), T1(50 AMPS), ISDN/DDS (fused)(50 AMPS), DIAL-UP/MODEM/FAX(fused)(75 AMPS), POWER OVER ETHERNET(MODE A)(50 AMPS), POWER OVER ETHERNET(MODE B)(Pins 1, 2, 3, & 6 - 132 amps Pins 4, 5, 7, & 8 - 50 amps), CCTV(132 AMPS), CABLE TV/SATELLITE(20ka(8/20 msec waveform)) RESPONSE TIME: Less than 5 nanoseconds MAXIMUM SHUNT CAPACITANCE: 10/100BASE T RS422, RS485, RS423, ETHERNET(
Citel - RAK-POE-60V-B-SO - Cylix RAK-PoE-60v-B-SO MODE B - RJ45, 100BASE T - 7.5v, PINS 1, 2, 3, 6 - 60v, PINS 4, 5, 7,
The RAK series of Rack Mount and Wall Mount Standoff protectors will ensure the reliable operation of networked equipment connected to 10/100/1000BASE T Ethernet, RS422, RS232, Lease Line, Power over Ethernet (PoE), ISDN, T1, DDS, Dial-Up, and most other communication interfaces. Transient surges can enter electronic equipment through any pathway provided. Facilities with reliable AC power protectors can still experience surge-related, system downtime. Transient surge energies from sources such as inductive load switching, ground loop currents and electrostatic discharge are clamped by AC protectors into the shared communication ground, resulting in damage to expensive communications hardware. The RAK Series includes 16 port, 19 relay rack protectors as well as 16 and 32 port, 5 standoff units for wall mount protection or environments where 19 relay rack space is limited. A wide variety of communication interfaces are supported that include 10/100/1000BASE T Ethernet, RS232, RS422, Power over Ethernet (PoE) and high speed LAN/WAN applications. All these features make RAK protectors the most cost effective and versatile devices of their kind available today. Whether you need to protect a single network concentrator, or an entire relay rack full of voltage sensitive equipment, Cylix RAK series protectors are an easy, cost effective solution to overvoltage problems. NOTE: This is a general description please see title for acutal product. State-of-the-art, avalanche diode technology Compact in-line installation Easy, hot swappable, single ports High speed, high energy handling capability Low shunt capacitance to reduce signal loss Convenient Front Input and Output or Standoff bracket for the full data cabinets STD. CLAMP VOLTAGE: 10/100BASE T RS422, RS485, RS423, ETHERNET(7.5 VOLTS), 1000 BASE T CATEGORY 6 ETHERNET(7.5 VOLTS), HIGH VOLTAGE ETHERNET(60 VOLTS), RS232(18 VOLTS), T1(60 VOLTS), ISDN/DDS (fused)(60 VOLTS), DIAL-UP/MODEM/FAX(fused)(240 VOLTS), POWER OVER ETHERNET(MODE A)(60 VOLTS), POWER OVER ETHERNET(MODE B)(Pins 1, 2, 3, & 6 - 7.5 volts Pins 4, 5, 7, & 8 - 60 volts), CCTV(7.5 VOLTS), CABLE TV/SATELLITE(90 VOLTS) PEAK PULSE CURRENT 10/1000 us s.c. wave form @Vcl: 10/100BASE T RS422, RS485, RS423, ETHERNET(132 AMPS), 1000 BASE T CATEGORY 6 ETHERNET(100 AMPS), HIGH VOLTAGE ETHERNET(45 AMPS), RS232(60 AMPS), T1(50 AMPS), ISDN/DDS (fused)(50 AMPS), DIAL-UP/MODEM/FAX(fused)(75 AMPS), POWER OVER ETHERNET(MODE A)(50 AMPS), POWER OVER ETHERNET(MODE B)(Pins 1, 2, 3, & 6 - 132 amps Pins 4, 5, 7, & 8 - 50 amps), CCTV(132 AMPS), CABLE TV/SATELLITE(20ka(8/20 msec waveform)) RESPONSE TIME: Less than 5 nanoseconds MAXIMUM SHUNT CAPACITANCE: 10/100BASE T RS422, RS485, RS423, ETHERNET(
